Repareer je spullen Gemeenschap Winkel

Shark Navigator Lightweight Upright Motherboard Replacement

Inleiding

The motherboard is the command center for the vacuum's functions. Sometimes components on the board will come loose and require replacement. This guide will show you the steps necessary to replace the motherboard.

Wat je nodig hebt

  1. Shark Navigator Lightweight Upright Motherboard Replacement, Head Shell: stap 1, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement, Head Shell: stap 1, afbeelding 2 van 2

    • Detach the hose connected on the bottom of the vacuum by pulling it out of the casing.

    Vertaal

  2. Shark Navigator Lightweight Upright Motherboard Replacement: stap 2, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 2, afbeelding 2 van 2

    • Lay the vacuum on its side.

    • Press in the black, rubberish button located on the back of the vacuum to detach the vacuum head from the body.

    Vertaal

  3. Shark Navigator Lightweight Upright Motherboard Replacement: stap 3, afbeelding 1 van 1

    • Flip over the vacuum head so the brush head is facing up.

    Vertaal

  4. Shark Navigator Lightweight Upright Motherboard Replacement: stap 4, afbeelding 1 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 4, afbeelding 2 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 4, afbeelding 3 van 3

    • Remove the small front wheels with a metal spudger by inserting the metal spudger in front of the wheel and slowly prying up. This will free the wheel and reveal the screw beneath it.

    • Repeat this for the other wheel.

    Vertaal

  5. Shark Navigator Lightweight Upright Motherboard Replacement: stap 5, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 5, afbeelding 2 van 2

    • Remove the two 18mm screws with a JIS 1 screwdriver.

    Vertaal

  6. Shark Navigator Lightweight Upright Motherboard Replacement: stap 6, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 6, afbeelding 2 van 2

    • Remove the four 18mm screws located on the top corners and the bottom/middle of the vacuum head using a JIS 1 screwdriver.

    Vertaal

  7. Shark Navigator Lightweight Upright Motherboard Replacement: stap 7, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 7, afbeelding 2 van 2

    • Remove the two 18mm screws located on the inside of the large wheels using a JIS 1 screwdriver.

    Vertaal

  9. Shark Navigator Lightweight Upright Motherboard Replacement: stap 8, afbeelding 1 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 8, afbeelding 2 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 8, afbeelding 3 van 3

    • Remove the plastic cover by prying the plastic cover up using a plastic opening tool.

    • Prying in multiple locations may be necessary to create separation.

    Vertaal

  10. Shark Navigator Lightweight Upright Motherboard Replacement, Motor: stap 9, afbeelding 1 van 1

    • Locate the motor on the top right corner of the vacuum head shell.

    Vertaal

  11. Shark Navigator Lightweight Upright Motherboard Replacement: stap 10, afbeelding 1 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 10, afbeelding 2 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 10, afbeelding 3 van 3

    • Remove the belt from the motor gear by sliding the belt to the right.

    Vertaal

  12. Shark Navigator Lightweight Upright Motherboard Replacement: stap 11, afbeelding 1 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 11, afbeelding 2 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 11, afbeelding 3 van 3

    • Remove the white metal wire connector from the motor.

    • The white cable is positive.

    Vertaal

  13. Shark Navigator Lightweight Upright Motherboard Replacement: stap 12, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 12, afbeelding 2 van 2

    • Remove the black metal wire connector from the motor.

    • The black cable is negative.

    Vertaal

  14. Shark Navigator Lightweight Upright Motherboard Replacement, Motherboard: stap 13, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement, Motherboard: stap 13, afbeelding 2 van 2

    • Remove the two 12mm screws using a JIS 1 screwdriver.

    Vertaal

  15. Shark Navigator Lightweight Upright Motherboard Replacement: stap 14, afbeelding 1 van 1

    • Remove the wire housing by removing one 12mm screw using a JIS 1 screwdriver.

    Vertaal

  16. Shark Navigator Lightweight Upright Motherboard Replacement: stap 15, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 15, afbeelding 2 van 2

    • Lift up the wire housing from the plastic base using tweezers.

    Vertaal

  17. Shark Navigator Lightweight Upright Motherboard Replacement: stap 16, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 16, afbeelding 2 van 2

    • Free the black and white cables that were previously attached to the motor from their slot.

    Vertaal

  18. Shark Navigator Lightweight Upright Motherboard Replacement: stap 17, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 17, afbeelding 2 van 2

    • Free the motherboard and its connecting parts from the rest of the vacuum.

    • Turn the motherboard upside-down and spread wires out.

    Vertaal

  19. Shark Navigator Lightweight Upright Motherboard Replacement: stap 18, afbeelding 1 van 2 Shark Navigator Lightweight Upright Motherboard Replacement: stap 18, afbeelding 2 van 2

    • Heat the wire connection's solder joint until the joint looks wet and liquidy.

    • While maintaining contact with the solder iron, free the wire end by pulling the wire away from the board with the tweezers.

    • For instructions on how to solder properly please refer to this soldering technique guide. Hoe moet je (de-)solderen?

    • Remember which cables were soldered onto where. You will have to re-solder the cables back onto the same joint.

    • Solder iron is extremely hot and should be handled with care. Always wear eye protection when soldering.

    Vertaal

  20. Shark Navigator Lightweight Upright Motherboard Replacement: stap 19, afbeelding 1 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 19, afbeelding 2 van 3 Shark Navigator Lightweight Upright Motherboard Replacement: stap 19, afbeelding 3 van 3

    • Completely free the cable by pulling it out of the board.

    • Repeat for the remaining cables. There are 4 total.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 3 andere bijdragers

Suzie

Lid sinds: 10/02/17

527 Reputatie

4 handleidingen geschreven

Medailles: 10

+7 andere badges

Team

Cal Poly, Team S4-G6, Livingston Fall 2017 Lid van Cal Poly, Team S4-G6, Livingston Fall 2017

CPSU-LIVINGSTON-F17S4G6

3 Leden

12 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 4

Altijd: 1,552