Repareer je spullen Gemeenschap Winkel

Ryobi RJ1861V Motor Housing Replacement

Wat je nodig hebt

  1. Ryobi RJ1861V Motor Housing Replacement, Saw Bar Assembly: stap 1, afbeelding 1 van 1

    • Use a Torx T5 screwdriver to remove the single 8 mm screw securing the shoe.

    Vertaal

  2. Ryobi RJ1861V Motor Housing Replacement: stap 2, afbeelding 1 van 2 Ryobi RJ1861V Motor Housing Replacement: stap 2, afbeelding 2 van 2

    • Remove the rubber sleeve.

    • You may have to use some force as it has a tight fit.

    Vertaal

  3. Ryobi RJ1861V Motor Housing Replacement: stap 3, afbeelding 1 van 1

    • Use a Torx T5 screwdriver to remove the six screws on the underside of the device.

    Vertaal

  4. Ryobi RJ1861V Motor Housing Replacement: stap 4, afbeelding 1 van 1

    • Use a Torx T5 screwdriver to remove the four screws on the top of the gear case.

    • There are two screws on each side of the device.

    Vertaal

  5. Ryobi RJ1861V Motor Housing Replacement: stap 5, afbeelding 1 van 1

    • Remove the backside panel.

    Vertaal

  7. Ryobi RJ1861V Motor Housing Replacement: stap 6, afbeelding 1 van 1

    • Unscrew the four T5 Torx screws that hold the assembly bar in place.

    Vertaal

  8. Ryobi RJ1861V Motor Housing Replacement: stap 7, afbeelding 1 van 1

    • Lift the assembly bar up and out of the chassis.

    Vertaal

  9. Ryobi RJ1861V Motor Housing Replacement, Assembly Bar Bearing: stap 8, afbeelding 1 van 1

    • Begin with the top of the device facing up.

    Vertaal

  10. Ryobi RJ1861V Motor Housing Replacement: stap 9, afbeelding 1 van 1

    • Insert needle nose pliers to remove the retaining pin at the top of the bearing.

    Vertaal

  11. Ryobi RJ1861V Motor Housing Replacement: stap 10, afbeelding 1 van 1

    • Once the retaining pin has been removed, pull off the damaged bearing and insert a new one.

    Vertaal

  12. Ryobi RJ1861V Motor Housing Replacement, Motor Housing: stap 11, afbeelding 1 van 2 Ryobi RJ1861V Motor Housing Replacement, Motor Housing: stap 11, afbeelding 2 van 2

    • After following prerequisite guides to get to the presented step, remove motor assembly from back housing.

    • Motor Assembly will be greasy

    • Motor Assembly

    • Motor Assembly Housing

    Vertaal

  13. Ryobi RJ1861V Motor Housing Replacement: stap 12, afbeelding 1 van 1

    • Using pliers to grab onto the elongated aluminium exterior of the housing, begin to slowly wiggle the motor assembly housing until it comes loose.

    Vertaal

  14. Ryobi RJ1861V Motor Housing Replacement: stap 13, afbeelding 1 van 1

    • Detach red wires from base of the back of the housing .

    Vertaal

  15. Ryobi RJ1861V Motor Housing Replacement: stap 14, afbeelding 1 van 1

    • After the wires have been detached it should be relatively easy to remove and replace the Motor Assembly Housing

    • Motor Assembly Housing

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 3

Altijd: 65