Ga door naar hoofdinhoud

Rival Mini Chopper MC-67BL Turning Gears Replacement

Wat je nodig hebt

  1. Rival Mini Chopper MC-67BL Turning Gears Replacement, Turning Gears: stap 1, afbeelding 1 van 2 Rival Mini Chopper MC-67BL Turning Gears Replacement, Turning Gears: stap 1, afbeelding 2 van 2
    • Twist the plastic lid counterclockwise to unlock it.

    • Lift the lid to remove it from the container.

  2. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 2, afbeelding 1 van 1
    • Carefully remove the blade from the container.

    • For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

  3. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 3, afbeelding 1 van 1
    • With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

  4. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 4, afbeelding 1 van 1
    • Use your fingers to pry out the two rubber feet from the bottom cover of the base.

    • The two feet furthest from the button tower contain screws. The other two feet do not.

  5. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 5, afbeelding 1 van 2 Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 5, afbeelding 2 van 2
    • Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

    • Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

  6. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 6, afbeelding 1 van 1
    • Firmly lift the bottom cover off of the base.

  7. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 7, afbeelding 1 van 1
    • Remove the smaller white gear by lifting it up with your hand.

  8. Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 8, afbeelding 1 van 3 Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 8, afbeelding 2 van 3 Rival Mini Chopper MC-67BL Turning Gears Replacement: stap 8, afbeelding 3 van 3
    • Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

    • Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

    • Continue turning the gear until completely removed from the blade-shaft.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Roxanne

Lid sinds: 10/17/13

522 Reputatie

4 handleidingen geschreven

Team

Cal Poly, Team 4-29, Amido Fall 2013 Lid van Cal Poly, Team 4-29, Amido Fall 2013

CPSU-AMIDO-F13S4G29

4 Leden

5 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 5

Altijd: 802