Repareer je spullen

Recht op reparatie

Onderdelen & Gereedschap

Rival 16131 Toaster bread grabber spring replacement

Geschreven door: Grant Haug (en 6 andere bijdragers)
  • Reacties: 0
  • Favorieten: 2
  • Voltooide reparaties: 1

Moeilijkheid

Gemiddeld

Stappen

8

Tijd vereist

10 minuten

Secties

2

Markeringen

4

Grammar Police

Grammaticapolitie

Laat je innerlijke leraar Nederlands vrij en help om de grammatica van deze handleiding te verbeteren!

Needs More Images

Er moeten meer foto's

Een paar extra plaatjes zouden de procedure in deze handleiding glashelder maken.

Step Trimmer

Stappen inkorten

Deze handleiding heeft onnodige stappen. Kort ze in om beknopter te kunnen zijn!

Better Introduction

Betere introductie

Verbeter deze handleiding door het afmaken of herzien van de introductie.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Make sure the toaster is unplugged before starting. Turn the toaster upside down and remove the rubber feet.

    • Make sure the toaster is unplugged before starting.

    • Turn the toaster upside down and remove the rubber feet.

    Bewerken

  2. Using a #2 Phillips head screwdriver, remove the four 12mm screws that attach the toaster shell. Using a #2 Phillips head screwdriver, remove the four 12mm screws that attach the toaster shell.

    • Using a #2 Phillips head screwdriver, remove the four 12mm screws that attach the toaster shell.

    Bewerken

  3. With the dial facing you, push the toaster base up and away until the base is just over the lip of the shell. This will disconnect the browning dial from the rest of the toaster. When reassembling the toaster, make sure that the back of the dial lines up with the slot both in position and orientation (the dial and slot are not perfect circles - they have a notch). The only object holding the shell onto the toaster now is the grey part of the lever.

    • With the dial facing you, push the toaster base up and away until the base is just over the lip of the shell. This will disconnect the browning dial from the rest of the toaster.

    • When reassembling the toaster, make sure that the back of the dial lines up with the slot both in position and orientation (the dial and slot are not perfect circles - they have a notch).

    • The only object holding the shell onto the toaster now is the grey part of the lever.

    Bewerken

  4. LCD iPhone-scherm fixkits

    De goedkope optie, ondersteund door onze levenslange garantie.

    Koop kits

    LCD iPhone-scherm fixkits

    Bespaar op reparatiekosten, niet op kwaliteit.

    Koop kits

  5. Reach under the shell and grab the back, white part of the lever.

    • Reach under the shell and grab the back, white part of the lever.

    • Grab the grey lever between your index finger and your middle finger and pull.

    • Pulling too hard will break the mechanism that holds the grey handle onto the white lever.

    • Remove the shell.

    Bewerken

  6. Locate the black, diamond shaped spring behind the white lever bracket.

    • Locate the black, diamond shaped spring behind the white lever bracket.

    Bewerken

  7. To remove the spring, use the tweezers to push the bottom edge of the spring out and around the metal bracket that keeps the springs in place.

    • To remove the spring, use the tweezers to push the bottom edge of the spring out and around the metal bracket that keeps the springs in place.

    • Repeat this for the other side.

    Bewerken

  8. Pulling the bottom of the spring out, lift the left circle up over the metal bracket that extends out from the bread grabbers.

    • Pulling the bottom of the spring out, lift the left circle up over the metal bracket that extends out from the bread grabbers.

    • Bring the right circle out, down, and around the bracket the extends out from the shelf that the toast would sits on.

    • Remove the right circle.

    Bewerken

  9. Make sure that all the angles are similar to the other metal spring.

    • Make sure that all the angles are similar to the other metal spring.

    • If not, then bend the broken spring to the angles of the correct spring.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 6 andere bijdragers

Grant Haug

Lid sinds: 26-09-12

139 Reputatie

4 handleidingen geschreven

Badges: 10

+7 andere badges

Team

Cal Poly, Team 2-8, Propen Fall 2012 Lid van Cal Poly, Team 2-8, Propen Fall 2012

CPSU-PROPEN-F12S2G8

5 Leden

6 handleidingen geschreven

0 Opmerkingen

Voeg een opmerking toe

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 2

Afgelopen 7 dagen: 5

Afgelopen 30 dagen: 24

Altijd: 2,499