Repareer je spullen Gemeenschap Winkel

Ring Stick Up Cam Camera Replacement

Inleiding

In this guide, we will show you how to replace the camera in a Ring Stick Up Cam. You will need a Phillips #00 screwdriver and a plastic opening tool.

Wat je nodig hebt

  1. Ring Stick Up Cam Camera Replacement, Battery: stap 1, afbeelding 1 van 1

    • Remove the six 6mm Phillips #00 screws from the back of the device.

    Bewerken

  2. Ring Stick Up Cam Camera Replacement: stap 2, afbeelding 1 van 1

    • Pry off the aluminum plate using a plastic opening tool.

    Bewerken

  3. Ring Stick Up Cam Camera Replacement: stap 3, afbeelding 1 van 1

    • Remove the two 6mm Phillips #00 screws that were under the aluminum plate.

    Bewerken

  4. Ring Stick Up Cam Camera Replacement: stap 4, afbeelding 1 van 1

    • Pry off the back cover using a plastic opening tool.

    Bewerken

  5. Ring Stick Up Cam Camera Replacement: stap 5, afbeelding 1 van 1

    • Disconnect the battery power leads using a plastic opening tool.

    Bewerken

  7. Ring Stick Up Cam Camera Replacement: stap 6, afbeelding 1 van 1

    • Use a plastic opening tool to loosen the adhesive holding the battery in place and remove the battery by hand.

    Bewerken

  8. Ring Stick Up Cam Camera Replacement, Camera: stap 7, afbeelding 1 van 1

    • Remove the three silver 6mm Phillips #00 screws holding the motherboard in the device.

    Bewerken

  9. Ring Stick Up Cam Camera Replacement: stap 8, afbeelding 1 van 1

    • Disconnect the ribbon connector shown in the photo.

    Bewerken

  10. Ring Stick Up Cam Camera Replacement: stap 9, afbeelding 1 van 1

    • Remove the motherboard from the device by hand.

    Bewerken

  11. Ring Stick Up Cam Camera Replacement: stap 10, afbeelding 1 van 1

    • Remove the two black 5mm Phillips #00 screws holding the camera board into the device.

    • Remove the single silver 10mm Phillips #00 screw holding the camera board into the device.

    Bewerken

  12. Ring Stick Up Cam Camera Replacement: stap 11, afbeelding 1 van 1

    • Remove the three plastic spacers shown in the photo by hand.

    Bewerken

  13. Ring Stick Up Cam Camera Replacement: stap 12, afbeelding 1 van 1

    • Carefully disconnect the camera board from the daughterboard by sliding a plastic opening tool between the camera board and the daughterboard.

    Bewerken

  14. Ring Stick Up Cam Camera Replacement: stap 13, afbeelding 1 van 1

    • Lift the camera board out of the housing using your hand.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 3 andere bijdragers

Ao Li

Lid sinds: 02/06/19

245 Reputatie

1 Handleiding geschreven

Medailles: 7

+4 andere badges

Team

UC Davis, Team S18-G3, Lore Winter 2019 Lid van UC Davis, Team S18-G3, Lore Winter 2019

UCD-LORE-W19S18G3

3 Leden

8 handleidingen geschreven

2 opmerkingen

Where can I purchase a new lens?

Javier Casas - Antwoord

Any ideas where to get a new lens?

Mete Doguoglu - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 14

Afgelopen 30 dagen: 41

Altijd: 4,454