Ga door naar hoofdinhoud

Deze handleiding heeft recentere wijzigingen. Schakel over naar de nieuwste niet-geverifieerde versie.

Removing the Logitech MBJ58 Mouse Scroll Wheel

Wat je nodig hebt

  1. Removing the Logitech MBJ58 Mouse Scroll Wheel, Top cover: stap 1, afbeelding 1 van 1
    • Hold the mouse so that the bottom is facing up.

    • Remove the single Phillips #1 screw from the bottom half of the mouse.

    باز کردن پیچ زیر موس

    h sh - Antwoord

    There may be a sticker covering the screw hole.

    Eric Jensen - Antwoord

  2. Removing the Logitech MBJ58 Mouse Scroll Wheel: stap 2, afbeelding 1 van 2 Removing the Logitech MBJ58 Mouse Scroll Wheel: stap 2, afbeelding 2 van 2
    • Place the mouse so that the bottom is resting against a hard surface.

    • Lift the top cover of the mouse gently, and remove it.

    جدا کردن قاب رو و زیر موس

    h sh - Antwoord

    The cover doesn’t lift straight up on my model - once you raise the back slightly as shown, gently pull it backward (parallel to the table top, away from the cord) to disengage two plastic clips that connect the bottom to the top.

    Eric Jensen - Antwoord

  3. Removing the Logitech MBJ58 Mouse Scroll Wheel, Removing the Logitech MBJ58 Mouse Scroll Wheel: stap 3, afbeelding 1 van 3 Removing the Logitech MBJ58 Mouse Scroll Wheel, Removing the Logitech MBJ58 Mouse Scroll Wheel: stap 3, afbeelding 2 van 3 Removing the Logitech MBJ58 Mouse Scroll Wheel, Removing the Logitech MBJ58 Mouse Scroll Wheel: stap 3, afbeelding 3 van 3
    • Locate the scroll wheel on the mouse.

    • Grab the scroll wheel with your thumb and index finger.

    • Gently lift up, to remove the scroll wheel from the mouse.

    خارج کردن چرخ اسکرول موس

    h sh - Antwoord

    Good information!

    My mouse is like new again.

    Many thanks

    Arie Dekker - Antwoord

Conclusie

To reassemble your device, follow these instructions in reverse order.

5 andere personen hebben deze handleiding voltooid.

Conor Whatley

Lid sinds: 01/11/13

489 Reputatie

3 handleidingen geschreven

Team

Cal Poly, Team 5-14, Forte Winter 2013 Lid van Cal Poly, Team 5-14, Forte Winter 2013

CPSU-FORTE-W13S5G14

5 Leden

21 handleidingen geschreven

2 opmerkingen

Thanks! The picture was what I needed after the mouse wheel parts came apart. My mouse is an M-BT58, but based on the numbers on the circuit board, there are probably several that are essentially the same. For others, here are some more details on putting things back together.

The mouse wheel has 4 parts:

1) The wheel itself (really a rubber tire and plastic rim, but they stay together)

2) Plastic carrier for the wheel

3) A spring for controlling rotation of the scroll wheel. This spring is at the top of the picture shown.

4) A spring for controlling clicks of the scroll wheel, shown near the wire leading to the computer.

Reassembly

1) Put spring (3) on carrier (2). There is a hole where the very tip of the end without the loop fits in.

2) Push the shorter axle of the mouse wheel into the carrier slightly depressing spring (3) as it is inserted. Once the wheel is inserted, the spring will stay in place.

3) Put spring (4) on the longer axle of the mouse wheel.

4) Install the carrier into the base of the mouse.

Jim Monte - Antwoord

I ran out of characters in the previous comment, but as you are installing the carrier into the base of the mouse, be sure to keep the spring (4) approximately as it is shown in the picture.

Jim Monte - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 25

Altijd: 5,557