Repareer je spullen Gemeenschap Winkel

Protocol Videodrone AP Battery Wiring Replacement

Inleiding

This guide will show you how to replace the battery and the soldering new wires to the motherboard. This is guide includes a highly recommend soldering guide. CAUTION: Soldering iron will be hot and may cause minor burns if handles improperly.

Wat je nodig hebt

  1. Protocol Videodrone AP Battery Wiring Replacement, Battery Wiring: stap 1, afbeelding 1 van 1

    • Make sure the drone is turned off

    Bewerken

  2. Protocol Videodrone AP Battery Wiring Replacement: stap 2, afbeelding 1 van 1

    • Open the hatch and carefully pull out the battery to expose the cable connection

    Bewerken

  3. Protocol Videodrone AP Battery Wiring Replacement: stap 3, afbeelding 1 van 2 Protocol Videodrone AP Battery Wiring Replacement: stap 3, afbeelding 2 van 2

    • Carefully pull apart the cable connection

    Bewerken

  5. Protocol Videodrone AP Battery Wiring Replacement: stap 4, afbeelding 1 van 2 Protocol Videodrone AP Battery Wiring Replacement: stap 4, afbeelding 2 van 2

    • Unscrew the 4 screws from the bottom of the drone.

    • Unscrew the 8 screws connecting the propeller guards to the drone

    • Unscrew the four propeller screws.

    • One screw is hidden behind the screwdriver.

    Bewerken

  6. Protocol Videodrone AP Battery Wiring Replacement: stap 5, afbeelding 1 van 1

    • Carefully remove faulty battery wiring from the drone

    Bewerken

  7. Protocol Videodrone AP Battery Wiring Replacement: stap 6, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    Tweezers
    $4.99
    Koop

    • Feed through opening using tweezers to grasp the wire and carefully pull through.

    Bewerken

  8. Protocol Videodrone AP Battery Wiring Replacement: stap 7, afbeelding 1 van 1

    • Use the soldering iron to solder new wires to mother board. CAUTION: Soldering iron may get hot and cause minor burns if handled improperly.

    • Use this guide for how to solder: https://www.youtube.com/watch?v=QKbJxytE...

    Bewerken

  9. Protocol Videodrone AP Battery Wiring Replacement: stap 8, afbeelding 1 van 1

    • Reattach the battery and test for power by turning on the drone and look for the 4 LEDs turn on.

    Bewerken
Conclusie

All Done!

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 5 andere bijdragers

Serge

Lid sinds: 09/26/17

340 Reputatie

3 handleidingen geschreven

Medailles: 8

+5 andere badges

Team

USF Tampa, Team S2-G1, Passmore Fall 2017 Lid van USF Tampa, Team S2-G1, Passmore Fall 2017

USFT-PASSMORE-F17S2G1

4 Leden

3 handleidingen geschreven

3 opmerkingen

Great explanation. Just wondering where to get the replacement piece. My drone has the black wire hanging by a single strand just outside the white connector. The red wire is in tact but I would need the whole part that attaches to the board and extends outside the drone to connect the battery to. Thanks

yasureok - Antwoord

Was wondering i think its charging the blue light flashes when plugged in but wont turn on. Wires look brand new

Michael Landry - Antwoord

I’m wondering the same thing, mine lights up blue when charging, wires look good but still no action.

Ryann Hunter -

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 14

Altijd: 1,793