Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.
Wat je nodig hebt
-
Deze stap is niet vertaald. Help het te vertalen
-
Locate the battery release tab on the underside of the G4.
-
Slide the battery release tab to the left and lift the battery out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the keyboard locking screw located in the middle of the keyboard so that it is parallel to the space bar. A half turn from parallel to parallel will unlock it. Another half turn will lock it again.
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Rest the keyboard face down on the trackpad area.
-
Disconnect the keyboard connector from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
-
Pull the RAM chip out.
-
Repeat this process if a second RAM chip is installed.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the seven T8 Torx screws from the lower case.
-
Using your thumbs, slide the lower case toward the front of the computer.
-
The lower case may stick in the front on a tab just above the center of the optical drive. Be careful as you work the case off, or you may break the thin strip of plastic just above the drive.
-
Lift the lower case off.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Firmly grasp the plastic tab attached to the Airport card and pull up and to the left.
-
Disconnect the antenna cable from the left side of the Airport card.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the hard drive by lifting the left edge up and out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect and remove the indicated orange ribbon cable.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the pink and white inverter cable from the inverter board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two silver T8 Torx screws from the black plastic bar.
-
Lift the black plastic bar out.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the two orange connectors from the logic board, removing tape as necessary.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the drive up on the right side so that you can access and disconnect the modem cable and inverter cable.
-
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the drive by lifting the right edge up and out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the large DC-In connector from the right side of the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two T6 Torx screws from the DC-In board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the DC-In board out of the computer by pulling up and away from you.
-
If there is a fan present, rotate the DC-In board slightly clockwise before easing it out at a slight angle in order to clear the fan clamp on top of it.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Before continuing, place a soft cloth on your work surface to rest the computer on. Turn the G4 over and place it on the cloth.
-
Disconnect the four indicated connectors from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the two connectors from the modem filter board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the T6 Torx screw from the modem filter board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the modem filter board from the computer by pulling up and to the right.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the G4 over.
-
Remove the seven T8 Torx screws from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the 5 indicated connectors from the logic board, removing tape as necessary.
-
Reassembly Tip: Reseating the logic board will be much easier if you use kapton tape to hold these five connectors out of the way until it is in place.
-
Caution: If taping the connectors back, be careful not to use tape with anything but very weak adhesive (i.e. kapton tape). Even electrical tape can pull the paint off the hinges when removed.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully lift the logic board up and pull it away from you.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two T8 Torx screws that secure the PC Card cage.
-
Remove the 4 mm hex nut from the PC Card cage.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the PC Card cage by pulling it to the right and twisting slightly toward you.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the four black T8 Torx screws from the plastic framework.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the G4 over.
-
Remove the five silver T8 Torx screws from the metal framework.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the G4 over.
-
Grasp the plastic framework and pull directly up.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect and remove the pink and white inverter cable, removing tape as necessary.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the audio connector cable on the right side of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Position the display approximately at a 45 degree angle and rest the computer on a soft cloth with the back panel ports facing up.
-
Remove the two T8 Torx screws from each clutch cover.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Close the display and pull off both clutch covers. You can use a non-metal flathead screwdriver if the clutch covers do not come off easily.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Open the back panel port cover and remove the four T6 Torx screws.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Open the display to a 90 degree angle. Rest the trackpad face down on your work surface and allow the display to hang over the edge. If possible, adjust your chair or worksurface height so the display will rest on your legs and the trackpad will lie flat on the worksurface.
-
Remove the four T8 Torx screws which fasten the display to the trackpad. The screw closest to the display data cable has a tapered head.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Grasp the metal heat exchanger and pull up and away from you. You may need to move the inverter cable on the right side of the computer in order to rotate the heat exchanger.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift up the metal brackets on either side of the upper case.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully thread the inverter cable on the right side through the slot in the upper case.
-
Carefully thread the display and backlight cables individually through the slot in the upper case. Be very careful with the display cable as it is easily damaged.
-
Remove the display assembly.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Re-align the metal heat exchanger with the upper case. Reconnect the audio connector cable on the right side of the upper case.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a spudger to pry the PRAM battery out of its housing on the upper case. Make sure not to bend the PRAM battery too much while prying it out.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Your upper case should look approximately like this.
-
Annuleren: ik heb deze handleiding niet afgemaakt.
6 andere personen hebben deze handleiding voltooid.