Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.
Wat je nodig hebt
-
Deze stap is niet vertaald. Help het te vertalen
-
Orient the computer so that the side with the line of screws on it is away from you.
-
Use your thumbs to push both battery release tabs away so that the edge of the battery lifts up.
-
Lift the battery out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the three identical Phillips screws from the memory door.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the memory door up enough so that you can get a grip on it, and slide it toward you, pulling it away from the casing.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
-
Pull the chip directly out from its connectors. If there is a second RAM chip installed, pop it out in the same manner.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
1) With your fingernails, grasp the locking bar on either side slide it a small amount (about 1/16" or 2 mm) towards the battery.
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Loosen the trackpad connector by pulling the locking bar toward the battery housing, using the tips of your fingers.
-
Slide the trackpad cable out of the loosened connector.
-
Note: When reassembling the case, the trackpad cable can get stuck below the slot to the motherboard. It's possible to nudge it out slowly by gently prodding it on either side with a small screwdriver. You don't need to use much force to do this. Eventually it will just pop back out and you can reconnect as per the instructions above. Also, note that the locking bar comes loose so if you see a little piece of plastic lying around when reassembling, that's what it is. :)
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following 10 screws from the bottom case:
-
Three 1.7 mm Phillips from the front edge of the battery compartment.
-
One 3.9 mm T8 Torx to the right of the memory card.
-
One 6.9 mm T8 Torx at the left edge of the memory compartment.
-
Three 12.4 mm fully threaded Phillips from the center of the row of screws along the back edge of the case.
-
Two 15.1 mm 2.5 mm threaded Phillips, one from either end of the row of screws along the back edge of the case.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the computer over and rotate it so that the DVI port faces you.
-
Remove the four identical Phillips screws spread along this edge of the case.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the computer 180 degrees so that the power receptacle faces you, and remove the four Phillips screws (identical to those in the last step).
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Open the computer and turn it so that the screen faces you.
-
Pull the upper case off, lifting from the back, and working around the edges.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a spudger to loosen the casing if it sticks.
-
Once the casing is entirely free, lift it off of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the four ( 3 - 6.9 mm & 1 - 4 mm) T8 Torx screws from the four corners of the SuperDrive.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully disconnect the orange optical drive ribbon from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the optical drive at the right, front corner, and slide it out of the computer (be careful not to catch the PRAM battery cable).
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the method described in the step for disconnecting the keyboard ribbon to loosen the connector on the DC-In board.
-
Pull the cable free of the loosened connector.
-
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the single Phillips screw from the Bluetooth board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the Bluetooth board partially out of the computer and disconnect the attached antenna cable.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the black speaker cable from the sound board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the single T8 Torx screw from the left speaker assembly.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the orange DC-In cable from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Deroute the cables from the right side of the speaker and lift it off of the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the rainbow power cable from the DC-In board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the black and white RJ-11 cable from the top, right corner of the modem.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two identical T8 Torx screws from the DC-In board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Slide the DC-In board to the right and lift it out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Close the display (cover it with a protective cloth, if you're worried about scratching the screen) and flip the computer over.
-
Disconnect the two cables and one ribbon in the RAM compartment.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Turn the laptop back over and open it up.
-
Remove the single T8 Torx screw from the right speaker assembly.
-
Deroute the display data cable from the left side of the speaker and pull the speaker assembly off the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
In order to deroute the speaker cable from the front edge of the logic board, you must disconnect the PRAM battery cable.
-
Deroute the speaker cable from the front edge of the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the 9 indicated cables from the logic board, starting in one place and moving around the board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following 12 T8 Torx screws from the logic board:
-
Four 3.9 mm, three along the front edge of the logic board, and one just above the right fan connector.
-
Three 6.9 mm large-headed screws in the upper, left corner of the logic board.
-
Five 6.9 mm scattered on the right half of the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a spudger to gently (very gently) pry up the left side of the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Grasp the logic board at the left edge with one hand and at the thinnest section with the other hand. Lift the left edge of the board up to approximately a 30 degree angle (if you don't have your protractor handy, just lift until the DVI port clears the right hinge).
-
Once the logic board clears the ports, slide it out to the left.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a firm plastic edge to scrape the thermal material off the raised copper heat conduit in three places. Clean the surface with rubbing alcohol.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a firm plastic edge to scrape the thermal material off the three indicated chips.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Apply a new layer of thermal paste to all three chips.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the inverter cable, the Bluetooth/DC-In cable, and the display data cable from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the Airport antenna cable at the gold connector, making sure you pull only on the gold metal portion of the connector.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the Bluetooth antenna cable from the Bluetooth board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove one T6 Torx screw from the upper, left corner of the left fan, and one from the upper, right corner of the right fan (2 screws total).
-
-
Deze stap is niet vertaald. Help het te vertalen
-
From each complete hinge assembly, remove two Torx T6 screws from the outside of each set, leaving two remaining in the middle of each hinge. On each side, the two screws closer to the edge of the computer are shorter than the two screws closer to the center of the computer. Then remove the two inner screws from each hinge assembly. There are 8 screws total.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
When reassembling the display, check to see that the hinges are seated properly before reinstalling the 8 screws of the two hinges. There is a metal phalange on the inside end of each hinge assembly that must be pointed downward and fit into a slot below the inside edge of the hinge. If not, the inside end of each hinge will sit too high and the plastic retaining bracket for the wiring will not sit down properly.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove seven Torx T8 screws from the heat sink and fan assembly.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the heat sink and fan assembly out of the computer.
-
Annuleren: ik heb deze handleiding niet afgemaakt.
7 andere personen hebben deze handleiding voltooid.