Ga door naar hoofdinhoud

Repareer je spullen

Recht op reparatie

Winkel

Inleiding

Use this guide to replace a faulty Playstation Move Motherboard.

  1. Using a Phillips #0 screwdriver,  remove the four 10mm screws located on the back of the device. Using a Phillips #0 screwdriver,  remove the four 10mm screws located on the back of the device. Using a Phillips #0 screwdriver,  remove the four 10mm screws located on the back of the device.
    • Using a Phillips #0 screwdriver, remove the four 10mm screws located on the back of the device.

  2. Insert the plastic opening tool at the indent. Gently use a forward and backward motion to safely pop open the cover.
    • Insert the plastic opening tool at the indent.

    • Gently use a forward and backward motion to safely pop open the cover.

    • Using your hands to further pull it apart.

  3. Once the device is opened, lift the battery out of the black plastic holder. Carefully pull the battery out and ensure that it's wires are still connected to the inside.
    • Once the device is opened, lift the battery out of the black plastic holder.

    • Carefully pull the battery out and ensure that it's wires are still connected to the inside.

  4. Using a Phillips head screwdriver, remove the 9mm screw located to the right of the battery, which is connected to  the inner plastic frame. Using the plastic opening tool carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire. Using the plastic opening tool carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire.
    • Using a Phillips head screwdriver, remove the 9mm screw located to the right of the battery, which is connected to the inner plastic frame.

    • Using the plastic opening tool carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire.

  5. Gently pull out the small grey cylindrical piece (vibrator). Removing this piece makes it easier to access the wire connection of the battery and remove it.
    • Gently pull out the small grey cylindrical piece (vibrator).

    • Removing this piece makes it easier to access the wire connection of the battery and remove it.

  6. Using tweezers, remove the small piece with a cylindrical top that is located to the left of the inner plastic frame. Using tweezers, remove the small piece with a cylindrical top that is located to the left of the inner plastic frame.
    • Using tweezers, remove the small piece with a cylindrical top that is located to the left of the inner plastic frame.

  7. Using one hand to hold the device, and the other hand to squeeze the inner plastic frame. Remove by squeezing the inner plastic frame, lift and pull it towards you. While removing the frame, be extremely careful because it could damage the frame or the motherboard.
    • Using one hand to hold the device, and the other hand to squeeze the inner plastic frame.

    • Remove by squeezing the inner plastic frame, lift and pull it towards you.

    • While removing the frame, be extremely careful because it could damage the frame or the motherboard.

  8. Gently pull on the white piece connecting the battery and the connector. Gently pull on the white piece connecting the battery and the connector.
    • Gently pull on the white piece connecting the battery and the connector.

  9. Remove the five 1.2 mm screws from upper portion of the controller. If you are replacing the trigger button, continue to step 13. If you are replacing the trigger button, continue to step 13.
    • Remove the five 1.2 mm screws from upper portion of the controller.

    • If you are replacing the trigger button, continue to step 13.

  10. Remove the two 1.2mm Phillips #1 screws. Remove the two 1.2mm Phillips #1 screws.
    • Remove the two 1.2mm Phillips #1 screws.

  11. Cautiously remove the circular white piece at the top without removing the LED inside. Cautiously remove the circular white piece at the top without removing the LED inside. Cautiously remove the circular white piece at the top without removing the LED inside.
    • Cautiously remove the circular white piece at the top without removing the LED inside.

  12. Remove the blue strip that is connected to the trigger button from the motherboard. Be careful to gently detach it from the motherboard. The strip may rip if too much strength is applied. Be careful to gently detach it from the motherboard. The strip may rip if too much strength is applied.
    • Remove the blue strip that is connected to the trigger button from the motherboard.

    • Be careful to gently detach it from the motherboard. The strip may rip if too much strength is applied.

  13. Remove the trigger button from the controller. Remove the trigger button from the controller.
    • Remove the trigger button from the controller.

  14. Remove the LED light by removing the white strip. If you are replacing the LED light, continue to Step 17. If you are replacing the LED light, continue to Step 17.
    • Remove the LED light by removing the white strip.

    • If you are replacing the LED light, continue to Step 17.

  15. Remove the motherboard from the plastic case. Remove the motherboard from the plastic case.
    • Remove the motherboard from the plastic case.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Destiny Jenkins

Lid sinds: 28-09-16

145 Reputatie

1 Handleiding geschreven

Team

USF Tampa, Team 3-3, Passmore Fall 2016 Lid van USF Tampa, Team 3-3, Passmore Fall 2016

USFT-PASSMORE-F16S3G3

4 Leden

8 handleidingen geschreven

Where does one obtain a replacement motherboard?

Tekkromancer - Antwoord

my controllers are also dying anyone know where to get a replacement board? I live in Canada

Jin - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 25

Altijd: 966