Ga door naar hoofdinhoud

Pentax Optio WG-3 GPS Motherboard Replacement

Wat je nodig hebt

  1. Pentax Optio WG-3 GPS Motherboard Replacement, Motherboard: stap 1, afbeelding 1 van 1
    • Turn over the camera so the screen is facing up.

    • Remove the four 5 mm Phillips #000 screws that secure the outer cover.

  2. Pentax Optio WG-3 GPS Motherboard Replacement: stap 2, afbeelding 1 van 1
    • Flip over the camera so the bottom is facing up.

    • Use the Phillips PH0005 again to remove one more 5mm screw.

    • Remove the cover.

  3. Pentax Optio WG-3 GPS Motherboard Replacement: stap 3, afbeelding 1 van 1
    • Remove the eight 5 mm Phillips #000 screws holding the circuitry together.

  4. Pentax Optio WG-3 GPS Motherboard Replacement: stap 4, afbeelding 1 van 1
    • Carefully remove the circuitry.

  5. Pentax Optio WG-3 GPS Motherboard Replacement: stap 5, afbeelding 1 van 1
    • There is a large silver sticker on top of the motherboard, gently remove it off of the motherboard.

  6. Pentax Optio WG-3 GPS Motherboard Replacement: stap 6, afbeelding 1 van 1
    • Gently use the spudger set to lift open the clamps that are holding the orange ribbons down.

    • Pull out the ribbons and remove the motherboard from the body of the camera.

  7. Pentax Optio WG-3 GPS Motherboard Replacement: stap 7, afbeelding 1 van 1
    • Remove the battery on the back of the motherboard.

  8. Pentax Optio WG-3 GPS Motherboard Replacement: stap 8, afbeelding 1 van 1
    • Unscrew and remove one 2 mm Phillips #00 screw to remove the flash component on the top of the circuitry.

  9. Pentax Optio WG-3 GPS Motherboard Replacement: stap 9, afbeelding 1 van 1
    • Remove three 5 mm Phillips #000 screws from the left side of the motherboard.

  10. Pentax Optio WG-3 GPS Motherboard Replacement: stap 10, afbeelding 1 van 1
    • Remove two ribbon cables from the small circuit.

    • Remove the ribbon cable that holds the sensor to the motherboard.

  11. Pentax Optio WG-3 GPS Motherboard Replacement: stap 11, afbeelding 1 van 1
    • The sensor is ready to be pulled out, carefully remove the sensor.

  12. Pentax Optio WG-3 GPS Motherboard Replacement: stap 12, afbeelding 1 van 1
    • Unscrew and remove three 5 mm screws from the front panel of the battery compartment.

  13. Pentax Optio WG-3 GPS Motherboard Replacement: stap 13, afbeelding 1 van 1
    • Pull the black panel away from the front panel.

  14. Pentax Optio WG-3 GPS Motherboard Replacement: stap 14, afbeelding 1 van 1
    • At the top of the circuit board there are three soldered dots that need to be unsoldered to remove the back of the battery component from the motherboard.

    • The motherboard can now be pulled and replaced.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Garrett Rose

Lid sinds: 03/31/22

373 Reputatie

2 handleidingen geschreven

Team

IUPUI, Team 3-1, Harley Spring 2022 Lid van IUPUI, Team 3-1, Harley Spring 2022

IUPUI-HARLEY-S22S3G1

3 Leden

3 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 7

Altijd: 245