Ga door naar hoofdinhoud

Inleiding

Prerequisite Only.

Onderdelen

Geen onderdelen opgegeven.

  1. Opening the iHome iH9, Backup Batteries: stap 1, afbeelding 1 van 3 Opening the iHome iH9, Backup Batteries: stap 1, afbeelding 2 van 3 Opening the iHome iH9, Backup Batteries: stap 1, afbeelding 3 van 3
    • Pull the tab towards you and lift up to remove the battery cover.

    • Remove the two AA batteries.

  2. Opening the iHome iH9, Opening the iHome iH9: stap 2, afbeelding 1 van 1
    • Unscrew the four 8mm Phillips #2 screws.

    • Unscrew the six 25mm Phillips #2 screws.

    • Reinstall the backup battery cover so it is out of the way.

  3. Opening the iHome iH9: stap 3, afbeelding 1 van 3 Opening the iHome iH9: stap 3, afbeelding 2 van 3 Opening the iHome iH9: stap 3, afbeelding 3 van 3
    • Pry the backplate up with a plastic opening tool between the back plate and the speaker grill.

    • Be careful when lifting the bottom plate up; there is a short white and orange 4-pin connector attached to its underside.

    • Lift the bottom plate up while making sure the connector remains attached.

  4. Opening the iHome iH9: stap 4, afbeelding 1 van 3 Opening the iHome iH9: stap 4, afbeelding 2 van 3 Opening the iHome iH9: stap 4, afbeelding 3 van 3
    • Use your hands to flip the backing plate away from you and rest it upside down on the iH9.

    • Unplug the white and orange 4-pin connector by pulling it in the direction of the wires.

    • Set the backing plate aside.

  5. Opening the iHome iH9: stap 5, afbeelding 1 van 1
    • Place the device so that the speaker grill is face down.

    • Remove the two 10mm Phillips #2 screws on interior sides of the speaker housings.

  6. Opening the iHome iH9: stap 6, afbeelding 1 van 2 Opening the iHome iH9: stap 6, afbeelding 2 van 2
    • Place the iH9 upside down.

    • Wires connect the core assembly to the housing; do not attempt to pull the core assembly completely out.

    • Using both hands, pull the housing siding away from the device while simultaneously lifting the motherboard and speaker assembly straight up.

    • Repeat for the other side.

  7. Opening the iHome iH9: stap 7, afbeelding 1 van 1
    • Stand the iH9 on its grill.

    • Separate the motherboard and speaker assembly by rocking it back and forth and pulling the assembly towards you.

    • Remove the small back panel.

  8. Opening the iHome iH9: stap 8, afbeelding 1 van 3 Opening the iHome iH9: stap 8, afbeelding 2 van 3 Opening the iHome iH9: stap 8, afbeelding 3 van 3
    • Firmly pull the wide 9-pin connector with black covering on the underside of the upper housing to unplug it.

    • Lay the housing and core assembly flat and close to each one another.

  9. Opening the iHome iH9: stap 9, afbeelding 1 van 2 Opening the iHome iH9: stap 9, afbeelding 2 van 2
    • Unplug the narrow 9-pin connector from the motherboard.

  10. Opening the iHome iH9: stap 10, afbeelding 1 van 1
    • Cut the zip tie holding the wires together with a wire cutter. The two sides of the device housing are now fully separated.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Curtis Wathne

Lid sinds: 31-01-15

397 Reputatie

3 handleidingen geschreven

Team

Cal Poly, Team 8-39, Amido Winter 2015 Lid van Cal Poly, Team 8-39, Amido Winter 2015

CPSU-AMIDO-W15S8G39

4 Leden

8 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 2

Altijd: 45