Ga door naar hoofdinhoud

Oliver Bagel and Bun Slicer 702-N Blade Replacement

Wat je nodig hebt

  1. Oliver Bagel and Bun Slicer 702-N Blade Replacement, Blade: stap 1, afbeelding 1 van 1
    • Remove the black knob underneath the bagel slicer base by twisting it counterclockwise.

  2. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 2, afbeelding 1 van 1
    • On the left end of the slicer, repeat the previous step to remove the bottom knob.

  3. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 3, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 3, afbeelding 2 van 2
    • Remove the knob located in the middle by twisting it counterclockwise.

    • After removing the knob, smoothly pull out the lock.

  4. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 4, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 4, afbeelding 2 van 2
    • Locate the knob on the left and repeat Step 3 to remove the knob and lock.

  5. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 5, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 5, afbeelding 2 van 2
    • While holding the ends of the bagel chute, lift the entire chute up and set it aside.

    • When you remove the chute, the sharp blade will be exposed. Take further caution as you proceed through the guide.

  6. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 6, afbeelding 1 van 3 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 6, afbeelding 2 van 3 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 6, afbeelding 3 van 3
    • Remove all three nuts on the blade cover.

    • It’s important to separate and organize the different small parts in each step to ensure a smooth reassembling process.

  7. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 7, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 7, afbeelding 2 van 2
    • Carefully lift up the blade cover and set aside.

  8. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 8, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 8, afbeelding 2 van 2
    • Remove the black knobs on both sides of the blade and set aside.

    • Make sure that you keep these knobs separate from the knobs in Steps 1-6 as they look identical but are not interchangeable between each other.

  9. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 9, afbeelding 1 van 1
    • Carefully lift up the part and set aside.

    • Hold the part by its ends so that your hands are as far from the blade as possible.

  10. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 10, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 10, afbeelding 2 van 2
    • Put on cut gloves before proceeding.

    • Using a 7/16 wrench, remove the three bolts.

    • You may spin the blade clockwise to make the removal process easier.

  11. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 11, afbeelding 1 van 1
    • Carefully the lift the blade up and set aside in a safe spot.

    • Now is a great time to clean and wipe down all individual parts if needed.

  12. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 12, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 12, afbeelding 2 van 2
    • With a new blade, place the blade down and align the holes with the holes of the bagel slicer base.

  13. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 13, afbeelding 1 van 1
    • Hold the blade with your non-dominant hand to keep it steady.

    • Screw back in all three bolts of the blade with your by twisting it clockwise.

  14. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 14, afbeelding 1 van 1
    • Once the bolts are somewhat secured, use the 7/16 wrench again to tighten them until firm.

  15. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 15, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 15, afbeelding 2 van 2
    • Insert the part with the outward sticking bolt and place the part down.

    • Make sure to align the outward sticking bolt's hole with the screw.

  16. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 16, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 16, afbeelding 2 van 2
    • Twist the black knobs clockwise on both sides of the part until firmly tight.

    • Make sure you are using the same black knobs you removed in Step 10.

  17. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 17, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 17, afbeelding 2 van 2
    • Align the holes of the bagel cover with the bolts and place the cover down.

  18. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 18, afbeelding 1 van 3 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 18, afbeelding 2 van 3 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 18, afbeelding 3 van 3
    • Twist all three nuts on the bagel cover clockwise until tight.

  19. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 19, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 19, afbeelding 2 van 2
    • On the bagel chute you removed in Step 5, align the lock's hole with the bolt.

    • Place a black knob on top and twist clockwise until tight.

  20. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 20, afbeelding 1 van 3 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 20, afbeelding 2 van 3 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 20, afbeelding 3 van 3
    • Repeat Step 19 for the other knob.

    • After completing Steps 19 and 20, your bagel chute should look like the third image.

  21. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 21, afbeelding 1 van 2 Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 21, afbeelding 2 van 2
    • Place the bagel chute on top of the metallic slicer base.

    • The bottom part of the lock should go underneath the base.

    • Line up the holes of the locks with the bolts and twist a black knob into the hole of the base.

    • Due to the obscure position of the bolt, you can insert the black knob into the lock first and move it back and forth until you feel a hole.

  22. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 22, afbeelding 1 van 1
    • Repeat Step 21 for the lock on the other side.

  23. Oliver Bagel and Bun Slicer 702-N Blade Replacement: stap 23, afbeelding 1 van 1
    • Plug in the power cord to an outlet and turn it on. If it doesn't make a loud screeching sound, you've successfully reassembled the bagel slicer!

Conclusie

To reassemble your device, follow these instructions in reverse order.

Andre Lam

Lid sinds: 02/03/23

337 Reputatie

1 Handleiding geschreven

Team

UC Davis, Team 1-3, Andersen Winter 2023 Lid van UC Davis, Team 1-3, Andersen Winter 2023

UCD-ANDERSEN-W23S1G3

2 Leden

1 handleiding geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 5

Afgelopen 30 dagen: 20

Altijd: 306