Inleiding

You need a T5 screwdriver to remove the screws.

Onderdelen

Geen onderdelen nodig.

In order to remove the back cover, you must press the indicated button.
  • In order to remove the back cover, you must press the indicated button.

Voeg opmerking toe

With the button pressed, apply light pressure and slide the back cover off. This will allow you to access the battery
  • With the button pressed, apply light pressure and slide the back cover off.

  • This will allow you to access the battery

Voeg opmerking toe

In order to remove the battery, pull it out from the same side that the rubber button is on.
  • In order to remove the battery, pull it out from the same side that the rubber button is on.

Voeg opmerking toe

Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone.
  • Using a plastic opening tool, separate the back cover from the phone.

Voeg opmerking toe

Continue along the edge with the plastic opening tool. Continue along the edge with the plastic opening tool.
  • Continue along the edge with the plastic opening tool.

Voeg opmerking toe

Gently, remove the back cover. Gently, remove the back cover. Gently, remove the back cover.
  • Gently, remove the back cover.

Voeg opmerking toe

Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver.
  • Unscrew the indicated screws using the T5 screwdriver.

Voeg opmerking toe

Open the phone up and use the plastic opening tool to remove the cover to the keyboard. Be careful not to break the plastic during this step; do your best not to force anything.
  • Open the phone up and use the plastic opening tool to remove the cover to the keyboard.

  • Be careful not to break the plastic during this step; do your best not to force anything.

Voeg opmerking toe

The button board will be loose once the cover is removed. Lift it up to reveal the sensor board.
  • The button board will be loose once the cover is removed.

  • Lift it up to reveal the sensor board.

Voeg opmerking toe

With the T5 Screwdriver, remove the marked screws. With the T5 Screwdriver, remove the marked screws.
  • With the T5 Screwdriver, remove the marked screws.

Voeg opmerking toe

With the screws removed, the sensor board should be free to flip up. With the screws removed, the sensor board should be free to flip up.
  • With the screws removed, the sensor board should be free to flip up.

Voeg opmerking toe

Disconnect the wire with the plastic opening tool. Disconnect the wire with the plastic opening tool.
  • Disconnect the wire with the plastic opening tool.

Voeg opmerking toe

Remove the screws marked. The Screw on the left is located underneath the cable. With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.
  • Remove the screws marked.

  • The Screw on the left is located underneath the cable.

  • With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

Cameron Weinberg

Lid sinds: 12-04-11

444 Reputatie

6 handleidingen geschreven

Team

Cal Poly, Team 18-21, Garner Spring 2011 Lid van Cal Poly, Team 18-21, Garner Spring 2011

CPSU-GARNER-S11S18G21

4 Leden

7 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 2

Afgelopen 7 Dagen: 9

Afgelopen 30 Dagen: 30

Altijd: 5,339