Inleiding

Introduction

In this guide, we show how to unscrew and remove the back case of the Nokia 2630b. This enables access to the motherboard, antenna, and LCD screen of the phone.

Onderdelen

Geen onderdelen nodig.

Press the release buttons located on either side of the battery cover Pull the battery cover away from the phone
  • Press the release buttons located on either side of the battery cover

  • Pull the battery cover away from the phone

Voeg opmerking toe

Gently pull the battery out of the phone with your fingers Gently pull the battery out of the phone with your fingers
  • Gently pull the battery out of the phone with your fingers

Voeg opmerking toe

Remove the two screws on either side of the battery case using the microscrewdriver using the T5 bit
  • Remove the two screws on either side of the battery case using the microscrewdriver using the T5 bit

    • The T5 bit has a star shaped end and has "T5" engraved on the side of the bit for easy identification

  • NOTE: Keep the screws in a safe place while you continue working.

Voeg opmerking toe

Separate the front case from the back case using the iPod opener NOTE: The keypad is a loose piece and may fall out NOTE: The keypad is a loose piece and may fall out
  • Separate the front case from the back case using the iPod opener

  • NOTE: The keypad is a loose piece and may fall out

Voeg opmerking toe

Remove screws using the same T5 screw bit to release the computer chip from the case
  • Remove screws using the same T5 screw bit to release the computer chip from the case

  • NOTE: Keep the screws in a safe place while you continue working

Voeg opmerking toe

Carefully lift the black frame off the screen with your fingers
  • Carefully lift the black frame off the screen with your fingers

Voeg opmerking toe

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Carefully remove the computer chip and screen out of the black case with your fingers
  • Carefully remove the computer chip and screen out of the black case with your fingers

Voeg opmerking toe

The screen is attached to the motherboard by an orange ribbon Carefully detach the ribbon from the motherboard using your fingers
  • The screen is attached to the motherboard by an orange ribbon

  • Carefully detach the ribbon from the motherboard using your fingers

Voeg opmerking toe

Reattach new screen by connecting the orange ribbon to the computer chip
  • Reattach new screen by connecting the orange ribbon to the computer chip

Voeg opmerking toe

Place computer chip and screen back into black case Place computer chip and screen back into black case
  • Place computer chip and screen back into black case

Voeg opmerking toe

Place black frame back over screen
  • Place black frame back over screen

Voeg opmerking toe

Carefully place keypad back in place Carefully place keypad back in place
  • Carefully place keypad back in place

Voeg opmerking toe

Snap the front case back in place with the bottom case with your fingers Snap the front case back in place with the bottom case with your fingers
  • Snap the front case back in place with the bottom case with your fingers

Voeg opmerking toe

Reassemble screws with microscrewdriver
  • Reassemble screws with microscrewdriver

Voeg opmerking toe

Slide battery back into place
  • Slide battery back into place

Voeg opmerking toe

Snap battery cover back into place
  • Snap battery cover back into place

Voeg opmerking toe

Locate the four screws that secure the back case to the rest of the phone. Unscrew all four screws using a "T-5" star shaped screw driver, turning counter-clockwise.
  • Locate the four screws that secure the back case to the rest of the phone.

  • Unscrew all four screws using a "T-5" star shaped screw driver, turning counter-clockwise.

Voeg opmerking toe

DO NOT PULL APART! There is a wire attaching the speaker to the rear case. It is very important to NOT sever this connection. Because of this, the rear case does not completely detach from the rest of the phone. Holding the rear case, applying pressure to the back of the phone near the location of the battery in order to separate the two components. Holding the rear case, applying pressure to the back of the phone near the location of the battery in order to separate the two components.
  • DO NOT PULL APART! There is a wire attaching the speaker to the rear case. It is very important to NOT sever this connection. Because of this, the rear case does not completely detach from the rest of the phone.

  • Holding the rear case, applying pressure to the back of the phone near the location of the battery in order to separate the two components.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Eric

Lid sinds: 07-04-11

51 Reputatie

5 handleidingen geschreven

Team

Cal Poly, Team 9-61, Walters Spring 2011 Lid van Cal Poly, Team 9-61, Walters Spring 2011

CPSU-WALTERS-S11S9G61

5 Leden

5 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 1

Afgelopen 7 Dagen: 2

Afgelopen 30 Dagen: 2

Altijd: 1,785