Ga door naar hoofdinhoud

Nokia 2610 Circuit Board Replacement

Wat je nodig hebt

  1. Nokia 2610 Circuit Board Replacement, Battery and Sim Card: stap 1, afbeelding 1 van 3 Nokia 2610 Circuit Board Replacement, Battery and Sim Card: stap 1, afbeelding 2 van 3 Nokia 2610 Circuit Board Replacement, Battery and Sim Card: stap 1, afbeelding 3 van 3
    • Place your thumb on the middle of the back cover and push it toward the bottom of the phone to slide the cover off.

  2. Nokia 2610 Circuit Board Replacement: stap 2, afbeelding 1 van 3 Nokia 2610 Circuit Board Replacement: stap 2, afbeelding 2 van 3 Nokia 2610 Circuit Board Replacement: stap 2, afbeelding 3 van 3
    • Use a plastic opening tool (or your finger) to gently pry the battery out of the battery slot on the back of the phone.

  3. Nokia 2610 Circuit Board Replacement: stap 3, afbeelding 1 van 3 Nokia 2610 Circuit Board Replacement: stap 3, afbeelding 2 van 3 Nokia 2610 Circuit Board Replacement: stap 3, afbeelding 3 van 3
    • Lift the metal sim card holder (at the bottom of the battery slot) up and carefully pry the sim card out of its slot with a plastic opening tool or your finger.

    • After removal, lower the metal sim card holder into its original position.

  4. Nokia 2610 Circuit Board Replacement, Front Pannel: stap 4, afbeelding 1 van 2 Nokia 2610 Circuit Board Replacement, Front Pannel: stap 4, afbeelding 2 van 2
    • Insert the plastic opening tool into the crack between the front and back panels.

    • Gently pry the front cover away from the back cover while sliding the plastic opening tool towards the top of the phone.

  5. Nokia 2610 Circuit Board Replacement: stap 5, afbeelding 1 van 2 Nokia 2610 Circuit Board Replacement: stap 5, afbeelding 2 van 2
    • Lift the bottom of the front cover away from the phone.

    • Continue lifting until the top of the front cover is fully removed from the phone.

    • Note: To replace the Keypad, gently lift it out of the front cover. It is located below the clear viewing window.

  6. Nokia 2610 Circuit Board Replacement, Circuit Board: stap 6, afbeelding 1 van 1
    • Use the Torx screwdriver with the T6 attachmet to remove the 6 .4 mm screws around the outside of the circuit board.

    • Note: Removing the 4 T6 screws around the screen will loosen it, so don't worry if the screen also separates from the circuit board.

  7. Nokia 2610 Circuit Board Replacement: stap 7, afbeelding 1 van 3 Nokia 2610 Circuit Board Replacement: stap 7, afbeelding 2 van 3 Nokia 2610 Circuit Board Replacement: stap 7, afbeelding 3 van 3
    • Lift the circuit board out of the back cover.

Conclusie

To reassemble your device, follow these instructions in reverse order.

5 andere personen hebben deze handleiding voltooid.

Andrew Wood

Lid sinds: 10/05/10

336 Reputatie

3 handleidingen geschreven

Team

Cal Poly, Team 7-52, Amido Fall 2010 Lid van Cal Poly, Team 7-52, Amido Fall 2010

CPSU-AMIDO-F10S7G52

4 Leden

12 handleidingen geschreven

Één opmerking

This is so cool tom!

Mo Chiggle - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 6

Altijd: 3,166