Ga door naar hoofdinhoud

Nintendo 3DS XL Left Bumper Replacement

Wat je nodig hebt

  1. Nintendo 3DS XL Left Bumper Replacement, Left Bumper: stap 1, afbeelding 1 van 1
    • Remove the SD card and the game cartridge from the device.

  2. Nintendo 3DS XL Left Bumper Replacement, Battery removal: stap 2, afbeelding 1 van 2 Nintendo 3DS XL Left Bumper Replacement, Battery removal: stap 2, afbeelding 2 van 2
    • Locate the battery cover panel on the back of the device.

    • Unscrew the two screws on the battery cover panel with a Phillips #00 screwdriver.

    • Remove the battery and battery cover panel.

  3. Nintendo 3DS XL Left Bumper Replacement: stap 3, afbeelding 1 van 1
    • Remove the four screws on the battery panel using the Phillips #00 screwdriver.

  4. Nintendo 3DS XL Left Bumper Replacement: stap 4, afbeelding 1 van 1
    • Locate the two screw covers on the bottom of the back panel, near the middle of the device.

    • These sticker-like covers are small, round, and made of rubber or plastic.

    • Insert the tip of a flathead screwdriver or spudger and gently pry the cover off by applying upward pressure.

    • You may need to wiggle the tool back and forth a bit to loosen the two covers.

    • Remove the two screws located behind the screw covers using a Phillips #00 screwdriver.

  5. Nintendo 3DS XL Left Bumper Replacement: stap 5, afbeelding 1 van 2 Nintendo 3DS XL Left Bumper Replacement: stap 5, afbeelding 2 van 2
    • Remove the screw near the game card compartment using a Phillips #00 screwdriver.

  6. Nintendo 3DS XL Left Bumper Replacement: stap 6, afbeelding 1 van 2 Nintendo 3DS XL Left Bumper Replacement: stap 6, afbeelding 2 van 2
    • Lift the back panel off of the device.

    • Be cautious not to pull any ribbons or cables from the motherboard as you remove the back panel.

    • Locate and disconnect the ribbon cables from the motherboard by gently pulling on the tabs that hold them in place.

  7. Nintendo 3DS XL Left Bumper Replacement: stap 7, afbeelding 1 van 2 Nintendo 3DS XL Left Bumper Replacement: stap 7, afbeelding 2 van 2
    • Remove the three left bumper assembly screws using Phillips #00 screwdriver.

    • Once the three screws are removed, gently remove the left bumper assembly from the device.

    • The spring may eject from the assembly as you remove it.

    • Remove the hinge pin from the bumper assembly.

  8. Nintendo 3DS XL Left Bumper Replacement: stap 8, afbeelding 1 van 1
    • Separate the bumper from the bumper assembly

  9. Nintendo 3DS XL Left Bumper Replacement: stap 9, afbeelding 1 van 2 Nintendo 3DS XL Left Bumper Replacement: stap 9, afbeelding 2 van 2
    Gereedschap gebruikt in deze stap:
    Microfiber Cleaning Cloths
    $3.99
    Koop
    • Using a spudger or a flathead screwdriver, gently pull the ribbon cable straight out of the connector in order to remove it.

    • The ribbon cable can be removed by other means such as using gloves or a microfiber cloth if preferred.

    • Replace the left bumper ribbon cable.

Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Jack Belcher

Lid sinds: 10/26/21

187 Reputatie

1 Handleiding geschreven

3 opmerkingen

No steps on how to install the new bumper?

Alex Tomalty - Antwoord

good but i wish there were reinstall instructions

Rowan Webb - Antwoord

I think that it's just basically do the steps backwards then you have it fixed.

Ender - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 7

Afgelopen 7 dagen: 41

Afgelopen 30 dagen: 231

Altijd: 5,304