Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

Nikon D90 Rear LCD Glass Replacement

Geschreven door: Ryan Lutz (en een andere inzender)
  • Reacties: 1
  • Favorieten: 3
  • Voltooide reparaties: 9

Moeilijkheid

Gemiddeld

Stappen

18

Tijd vereist

Stel een tijd voor??

Secties

3

Markeringen

0

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Slide the eyepiece up and off the viewfinder. Slide the eyepiece up and off the viewfinder.

    • Slide the eyepiece up and off the viewfinder.

    Bewerken

  2. Using a PH000 screwdriver, remove the two 4.8mm Phillips screws from the back of the viewfinder.

    • Using a PH000 screwdriver, remove the two 4.8mm Phillips screws from the back of the viewfinder.

    • Some screws may be JIS. Be wary of this if your PH000 does not feel like it is properly gripping the screws.

    Bewerken

  3. Remove the two 6.4mm Phillips screws on the right side of the camera, near the SD card slot.

    • Remove the two 6.4mm Phillips screws on the right side of the camera, near the SD card slot.

    Bewerken

  4. Remove the two 6.4mm Phillips screws on the left side of the camera, near the I/O ports.

    • Remove the two 6.4mm Phillips screws on the left side of the camera, near the I/O ports.

    Bewerken

  5. On the bottom of the camera,

    • On the bottom of the camera,

    • remove the two 5.3mm Phillips screws

    • and the other two 6.3mm Phillips screws.

    Bewerken

  6. Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step. Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step. Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step.

    • Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step.

    Bewerken

  7. Android Fix Kits

    A new screen or battery is one kit away.

    Nu winkelen

    Android Fix Kits

    A new screen or battery is one kit away.

    Nu winkelen

  8. Lift the rear case off of the back of the camera. Don't pull the casing completely off yet, as the ribbon cables are still connected.

    • Lift the rear case off of the back of the camera.

    • Don't pull the casing completely off yet, as the ribbon cables are still connected.

    • Be mindful of the two clips, making sure to keep the bottom panel far enough away to clear them.

    Bewerken

  9. Set the rear casing off to the side so you can access the ZIF connectors.

    • Set the rear casing off to the side so you can access the ZIF connectors.

    • The orientation shown in the picture seems to be the best position for the casing to sit comfortably without stressing the ribbon cable connections.

    Bewerken

  10. Disconnect the ribbon cables from their respective ZIF connectors on the logic board. Disconnect the ribbon cables from their respective ZIF connectors on the logic board. Disconnect the ribbon cables from their respective ZIF connectors on the logic board.

    • Disconnect the ribbon cables from their respective ZIF connectors on the logic board.

    Bewerken

  11. Separate the rear casing from the camera.

    • Separate the rear casing from the camera.

    Bewerken

  12. Peel back the yellow tape covering the cable connector on the back of the casing you removed.

    • Peel back the yellow tape covering the cable connector on the back of the casing you removed.

    Bewerken

  13. Using the spudger, rock the connector back and forth to disconnect the cable. Using the spudger, rock the connector back and forth to disconnect the cable. Using the spudger, rock the connector back and forth to disconnect the cable.

    • Using the spudger, rock the connector back and forth to disconnect the cable.

    Bewerken

  14. Remove the eight Phillips screws securing the brackets to the rear casing. Four 4.2mm screws securing the large metal bracket.

    • Remove the eight Phillips screws securing the brackets to the rear casing.

    • Four 4.2mm screws securing the large metal bracket.

    • Four 3.4mm screws securing the bracket that covers the ribbon cable.

    Bewerken

  15. Remove the silver metal plate. Remove the silver metal plate.

    • Remove the silver metal plate.

    Bewerken

  16. Fold the ribbon cables up and out of the way. Remove the metal shield covering the LCD.

    • Fold the ribbon cables up and out of the way.

    • Remove the metal shield covering the LCD.

    Bewerken

  17. Lift and remove the LCD from the rear case. Lift and remove the LCD from the rear case.

    • Lift and remove the LCD from the rear case.

    Bewerken

  18. Using either the iOpener or a heat gun, heat the rear LCD glass enough to melt the adhesive holding it on. The glass will be hot! Let cool before handling.

    • Using either the iOpener or a heat gun, heat the rear LCD glass enough to melt the adhesive holding it on.

    • The glass will be hot! Let cool before handling.

    Bewerken

  19. Push the glass out from the back side.

    • Push the glass out from the back side.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

9 andere personen hebben deze handleiding voltooid.

Auteur

met 1 andere bijdrager

Ryan Lutz

Lid sinds: 27-09-11

2.771 Reputatie

3 handleidingen geschreven

Badges: 32

+29 andere badges

0 Opmerkingen

Een opmerking toevoegen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 1

Afgelopen 7 Dagen: 1

Afgelopen 30 Dagen: 11

Altijd: 3,281