Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

Nikon D90 Rear Case Replacement

Geschreven door: Ryan Lutz (en 4 andere bijdragers)
  • Reacties: 2
  • Favorieten: 1
  • Voltooide reparaties: 8

Moeilijkheid

Gemiddeld

Stappen

10

Tijd vereist

Stel een tijd voor??

Secties

1

Markeringen

0

  1. Slide the eyepiece up and off the viewfinder. Slide the eyepiece up and off the viewfinder.

    • Slide the eyepiece up and off the viewfinder.

    Bewerken

  2. Using a PH000 screwdriver, remove the two 4.8mm Phillips screws from the back of the viewfinder.

    • Using a PH000 screwdriver, remove the two 4.8mm Phillips screws from the back of the viewfinder.

    • Some screws may be JIS. Be wary of this if your PH000 does not feel like it is properly gripping the screws.

    Bewerken

  3. Remove the two 6.4mm Phillips screws on the right side of the camera, near the SD card slot.

    • Remove the two 6.4mm Phillips screws on the right side of the camera, near the SD card slot.

    Bewerken

  4. Remove the two 6.4mm Phillips screws on the left side of the camera, near the I/O ports.

    • Remove the two 6.4mm Phillips screws on the left side of the camera, near the I/O ports.

    Bewerken

  5. Gratis verzending van alle bestellingen van meer dan US$ 100 of met een Pro Tech Toolkit!

    Doorblader onze winkel

  6. On the bottom of the camera,

    • On the bottom of the camera,

    • remove the two 5.3mm Phillips screws

    • and the other two 6.3mm Phillips screws.

    Bewerken

  7. Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step. Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step. Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step.

    • Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step.

    Bewerken

  8. Lift the rear case off of the back of the camera. Don't pull the casing completely off yet, as the ribbon cables are still connected.

    • Lift the rear case off of the back of the camera.

    • Don't pull the casing completely off yet, as the ribbon cables are still connected.

    • Be mindful of the two clips, making sure to keep the bottom panel far enough away to clear them.

    Bewerken

  9. Set the rear casing off to the side so you can access the ZIF connectors.

    • Set the rear casing off to the side so you can access the ZIF connectors.

    • The orientation shown in the picture seems to be the best position for the casing to sit comfortably without stressing the ribbon cable connections.

    Bewerken

  10. Disconnect the ribbon cables from their respective ZIF connectors on the logic board. Disconnect the ribbon cables from their respective ZIF connectors on the logic board. Disconnect the ribbon cables from their respective ZIF connectors on the logic board.

    • Disconnect the ribbon cables from their respective ZIF connectors on the logic board.

    Bewerken

  11. Separate the rear casing from the camera.

    • Separate the rear casing from the camera.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

8 andere personen hebben deze handleiding voltooid.

Auteur

met 4 andere bijdragers

Ryan Lutz

Lid sinds: 27-09-11

2.729 Reputatie

3 handleidingen geschreven

Badges: 32

+29 andere badges

2 Opmerkingen

Een opmerking toevoegen

good guidance,easy to follow,thanks

ramalingeswarao kaza - Antwoord

I want to replace my Nikon D90 DSLR bad LCD, this guide will save me from costly repairs.

ramalingeswarao kaza - Antwoord

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 6

Afgelopen 30 Dagen: 23

Altijd: 3,043