Ga door naar hoofdinhoud

Repareer je spullen

Recht op reparatie

Onderdelen & Gereedschap

Inleiding

This will show you how to open up the camera and replace the camera flash.

Onderdelen

Geen onderdelen opgegeven.

  1. Turn the front of the camera toward you.
    • Turn the front of the camera toward you.

  2. On the left side of the camera, use a Phillips #00 Precision Screwdriver to remove the two marked screws. On the left side of the camera, use a Phillips #00 Precision Screwdriver to remove the two marked screws. On the left side of the camera, use a Phillips #00 Precision Screwdriver to remove the two marked screws.
    • On the left side of the camera, use a Phillips #00 Precision Screwdriver to remove the two marked screws.

  3. On the right side of the camera, remove the first visible screw above the  HDMI and A/V OUT cover.
    • On the right side of the camera, remove the first visible screw above the HDMI and A/V OUT cover.

  4. Lift the HDMI and A/V OUT cover to access the hidden screw between the two ports.
    • Lift the HDMI and A/V OUT cover to access the hidden screw between the two ports.

    • Remove the screw

  5. Flip the camera upside down and remove the seven marked screws.
    • Flip the camera upside down and remove the seven marked screws.

  6. Nintendo Switch-kits

    Een snelle oplossing die je weer mee laat doen

    Koop Switchkits

    Nintendo Switch-kits

    Een snelle oplossing die je weer mee laat doen

    Koop Switchkits
  7. Turn the back of the camera toward you. Lift the display panel and remove the two marked screws
    • Turn the back of the camera toward you.

    • Lift the display panel and remove the two marked screws

  8. Use a plastic iFixit opening tool to gently loosen the top and sides of the camera. Use a plastic iFixit opening tool to gently loosen the top and sides of the camera. Use a plastic iFixit opening tool to gently loosen the top and sides of the camera.
    • Use a plastic iFixit opening tool to gently loosen the top and sides of the camera.

  9. Before fully opening the camera, identify the two marked ribbon cables
    • Before fully opening the camera, identify the two marked ribbon cables

    • Properly detach the ribbons before proceeding

  10. Carefully open the camera.
    • Carefully open the camera.

    • Now you have partial access to the camera's motherboard.

  11. Remove the five indicated screws that are attached to the metal plate.
    • Remove the five indicated screws that are attached to the metal plate.

  12. Remove the hidden top screw that is attached to the metal plate.
    • Remove the hidden top screw that is attached to the metal plate.

  13. Use a plastic iFixit opening tool to carefully loosen the metal plate.
    • Use a plastic iFixit opening tool to carefully loosen the metal plate.

    • Remove the metal plate to access the camera's motherboard.

  14. Now you have access to the camera's motherboard
    • Now you have access to the camera's motherboard

  15. Remove the screw that is located on the left of the view finder.
    • Remove the screw that is located on the left of the view finder.

  16. Carefully detach the two ribbon cables and detach the viewfinder.
    • Carefully detach the two ribbon cables and detach the viewfinder.

Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Nghiem Ngo

Lid sinds: 15-01-15

309 Reputatie

2 handleidingen geschreven

Team

USF Tampa, Team 1-1, Tanski Winter 2015 Lid van USF Tampa, Team 1-1, Tanski Winter 2015

USFT-TANSKI-W15S1G1

3 Leden

8 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 4

Altijd: 584