Repareer je spullen Gemeenschap Winkel

Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement

Inleiding

This guide describes the steps necessary to remove and replace the LCD Monitor Connecting Arm of a Nikon Coolpix L830 camera.

Wat je nodig hebt

  1. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement, Back Casing: stap 1, afbeelding 1 van 1

    • Use a Phillips #000 screwdriver to unscrew the two 3.0mm Phillips screws located on the side of the camera with the HDMI port.

    • The HDMI port side will be on the left if you are looking at the back of the camera with the LCD monitor.

    • One screw is located under the gray flap.

    Vertaal

  2. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 2, afbeelding 1 van 1

    • Unscrew the five 3.0mm Phillips #000 screws that are located on the bottom side of the camera.

    Vertaal

  3. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 3, afbeelding 1 van 1

    • Unscrew the 4.0mm Phillips #000 screw located underneath the grey flap on the side of the camera with the "DC IN 5.0 V" marker.

    • This will be on the right if you are looking at the back LCD monitor side.

    • Unscrew the exposed 3.0mm Phillips #000 screw on the same side.

    Vertaal

  5. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 4, afbeelding 1 van 1

    • Press the flash button to open the flash component.

    • Remove the 3.0mm Phillips #000 screw located directly in-between the two arms.

    Vertaal

  6. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 5, afbeelding 1 van 1

    • Open the LCD monitor to reveal two 2.0mm Phillips screws.

    • Remove the 2.0mm Phillips #000 screws.

    Vertaal

  7. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 6, afbeelding 1 van 2 Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 6, afbeelding 2 van 2

    • Make sure to open the plastic grey flaps on either side of the camera before proceeding with this step.

    • Insert a plastic opening tool between the back and front surface components of the camera.

    • Wiggle the plastic opening tool backwards and forwards along the top edge until the back surface comes off.

    • Remove the back casing gently to not damage the LCD ribbon connector or inner camera components.

    Vertaal

  8. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 7, afbeelding 1 van 2 Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 7, afbeelding 2 van 2

    • Gently pull the LCD ribbon connector up to allow the back casing to be completely removed.

    Vertaal

  9. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement, LCD Connecting Arm: stap 8, afbeelding 1 van 1

    • On the inside of the back cover, remove the two 2.0mm Phillips screws surrounding the connecting cable.

    Vertaal

  10. Nikon Coolpix L830 LCD Monitor Connecting Arm Replacement: stap 9, afbeelding 1 van 1

    • Gently pull the ribbon connector in order to remove the complete LCD Monitor Connecting Arm.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 3 andere bijdragers

Alex Delony

Lid sinds: 11/01/16

184 Reputatie

1 Handleiding geschreven

Medailles: 6

+3 andere badges

Team

Baylor, Team 4-4, Williams Fall 2016 Lid van Baylor, Team 4-4, Williams Fall 2016

BU-WILLIAMS-F16S4G4

3 Leden

10 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 3

Altijd: 474