Using two fingers, push up on the rear cover.
  • Using two fingers, push up on the rear cover.

Voeg opmerking toe

The rear cover slides up and off.
  • The rear cover slides up and off.

Voeg opmerking toe

  • Using the plastic opening tools, pry the left bottom corner of the battery up.

Voeg opmerking toe

  • Pull the battery up and out.

Voeg opmerking toe

  • Remove the two Torx T5 screws.

  • Remove the one Philips #00 screw.

#0 Phillis screw

skuhry - Antwoord

  • Using the plastic opening tool, pry up the battery housing upwards.

  • Push pry tool down, undoing the plastic tab.

Voeg opmerking toe

  • Pry the upper left tab open on the battery housing.

Voeg opmerking toe

  • Pry the top tab of the battery housing.

Voeg opmerking toe

  • Pry the right side tab of the battery housing.

Voeg opmerking toe

  • Pull up on the battery housing.

  • Slide the battery housing out to remove it.

Voeg opmerking toe

  • Using the plastic opening tool, push the blade into the space between the case and lower cover.

  • Turn the opening tool slightly, the lower cover will detach on that side.

  • Repeat on other side of the seam.

  • The lower cover will slide off.

Voeg opmerking toe

  • Remove the one T5 Torx screw

  • Remove the one #00 Philips screw

  • Lift up the end of the antenna housing and slide it outwards.

Voeg opmerking toe

  • Using the spudger, pry upwards on the second microphone connector.

Voeg opmerking toe

  • Pull up on the ribbon cable, the tape will detach from the main board ribbon.

Voeg opmerking toe

  • Pry the antenna cable up.

Voeg opmerking toe

  • Carefully pull up on the microphone board to release the tape from the phone.

Voeg opmerking toe

  • Insert the spudger under the connector.

  • Push the spudger up and twist to release the connector.

  • Repeat for the next connector.

Voeg opmerking toe

  • Push on the USB port to expose the black connector.

  • Use the spudger to pry the connector upwards.

The philips screw holding down the logic board (at the lower right corner in the picture) has to be removed before the board can be pushed back.

Mark - Antwoord

  • Place the spugder under the antenna connector.

  • Pry connector up vertically.

Voeg opmerking toe

  • Insert the spudger into tab above the camera.

  • Slide upwards until the board detaches from the case.

A philips screw holding down the upper logic board (in the lower left corner of the picture) must be remobed before the board can be detached.

Mark - Antwoord

  • Press the pointed tip of the spudger into the space below the button assembly.

  • Wiggle the spudger tip towards the outside of the button.

  • The button assembly is under some tension and may fly off.

Voeg opmerking toe

  • Push the pointed tip of the spudger into the base of the side button board.

  • Lift up, the board will disconnect from the case.

Voeg opmerking toe

  • Push on the lower motherboard until it slides under the case support.

  • The motherboard assembly comes out as a single piece.

  • Save the small black rubber rectangular sound guide under the motherboard, to replace over the microphone.

Be carefull not to tear the home button cable that is in the top right corner!!

zack - Antwoord

  • Using the spudger, lift the blue colored connector.

  • Use the supdger to lift the black connetor up as well.

  • Detach the upper motherboard from the lower motherboard.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Niklas Johnson

Lid sinds: 31-01-12

1.063 Reputatie

18 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 1

Altijd: 3,737