Ga door naar hoofdinhoud

Onderdelen

Geen onderdelen opgegeven.

  1. Lay the Nerf Strongarm on its side, left side facing up. Lay the Nerf Strongarm on its side, left side facing up.
    • Lay the Nerf Strongarm on its side, left side facing up.

  2. Locate the 12 Philips head screws and remove them:  Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm Locate the 12 Philips head screws and remove them:  Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
    • Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm

  3. Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
    • Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.

    • The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.

  4. At this time, remove the blaster cover to reveal its internals.
    • At this time, remove the blaster cover to reveal its internals.

    • If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.

  5. Once the screws have been removed, lift the top half of the gun off.
    • Once the screws have been removed, lift the top half of the gun off.

    • Notice, the gray colored piece must be removed first in order for the larger half to be removed.

    • Take care and try not to lose any smaller pieces as you open it up.

    • Locking tab for attachments.

  6. Locate the trigger mechanism's assembly, and notice that it's held in place by a single philip's head screw. Remove it. Screw specifications: Philips head, Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
    • Locate the trigger mechanism's assembly, and notice that it's held in place by a single philip's head screw. Remove it.

    • Screw specifications: Philips head, Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm

  7. Inspect the orange parts for signs of damage and debris. Any broken pieces must be replaced. This is the spring that controls the trigger. Through regular use, the  spring may become mangled or damaged. If it becomes damaged, a spring from a ballpoint pen can function as a decent replacement. This is the spring that controls the trigger. Through regular use, the  spring may become mangled or damaged. If it becomes damaged, a spring from a ballpoint pen can function as a decent replacement.
    • Inspect the orange parts for signs of damage and debris. Any broken pieces must be replaced.

    • This is the spring that controls the trigger. Through regular use, the spring may become mangled or damaged. If it becomes damaged, a spring from a ballpoint pen can function as a decent replacement.

Conclusie

To reassemble your device, follow these instructions in reverse order.

4 andere personen hebben deze handleiding voltooid.

Alexander Kim

Lid sinds: 27-08-15

718 Reputatie

3 handleidingen geschreven

Team

USF Tampa, Team 5-4, Blackwell Fall 2015 Lid van USF Tampa, Team 5-4, Blackwell Fall 2015

USFT-BLACKWELL-F15S5G4

4 Leden

10 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 8

Afgelopen 7 dagen: 62

Afgelopen 30 dagen: 221

Altijd: 13,062