Ga door naar hoofdinhoud

Makita Jack Hammer HM1203C 2010 Power Cord Replacement

Wat je nodig hebt

  1. Makita Jack Hammer HM1203C 2010 Power Cord Replacement, Remove the handle cover: stap 1, afbeelding 1 van 1
    • Make sure the hammer is disconnected from power before beginning any repair.

    • Use a Phillips #2 screwdriver to remove two screws securing the handle cover.

  2. Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 2, afbeelding 1 van 2 Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 2, afbeelding 2 van 2
    • Swing the bottom of the handle cover away from the hammer, then pull the cover down, toward the power cord, to remove it.

  3. Makita Jack Hammer HM1203C 2010 Power Cord Replacement, Remove the power cord: stap 3, afbeelding 1 van 1
    • Use a Phillips #2 screwdriver to remove the screw securing the power cord bracket.

  4. Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 4, afbeelding 1 van 2 Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 4, afbeelding 2 van 2
    • Lift the bottom edge of the bracket away from the hammer slightly, then pull down to remove it.

    • During reassembly, make sure the top hooked part of the bracket is inserted properly into its slot.

  5. Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 5, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    Flathead 3/32" or 2.5 mm Screwdriver
    $5.49
    Koop
    • Use a 2.5 mm flathead screwdriver to loosen the two set screws holding in the power cord wires.

  6. Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 6, afbeelding 1 van 3 Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 6, afbeelding 2 van 3 Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 6, afbeelding 3 van 3
    • Remove the power cord.

  7. Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 7, afbeelding 1 van 2 Makita Jack Hammer HM1203C 2010 Power Cord Replacement: stap 7, afbeelding 2 van 2
    • Slide the power cord guard off of the power cord.

    • During reassembly, install this guard on the new power cord.

  8. Makita Jack Hammer HM1203C 2010 Power Cord Replacement, Prepare the new power cord: stap 8, afbeelding 1 van 2 Makita Jack Hammer HM1203C 2010 Power Cord Replacement, Prepare the new power cord: stap 8, afbeelding 2 van 2
    • Use 10 gauge wire strippers to strip about 1/8 inch of insulation off of each wire of the new power cord.

Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

Adam O'Camb

Lid sinds: 04/11/15

199.443 Reputatie

416 handleidingen geschreven

Één opmerking

What does the flashing red indicator light indicate specifically? The green light is on but the red light underneath is also flashing.

MARK - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 7

Afgelopen 30 dagen: 46

Altijd: 1,577