Repareer je spullen Gemeenschap Winkel

Mad Catz Street Fighter IV FightPad Circuit Board Replacement

Inleiding

Use this as a guide to remove the motherboard so you can access the FightPad's buttons and directional pad.

Wat je nodig hebt

  1. Mad Catz Street Fighter IV FightPad Circuit Board Replacement, Rear and Side Case: stap 1, afbeelding 1 van 1

    • Use tweezers to completely remove the sticker from the rear of controller.

    Bewerken

  2. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 2, afbeelding 1 van 1

    • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    Bewerken

  3. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 3, afbeelding 1 van 2 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 3, afbeelding 2 van 2

    • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

    • Use the plastic opening tool to pry the two cases apart.

    Bewerken

  5. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 4, afbeelding 1 van 2 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 4, afbeelding 2 van 2

    • Remove the two rubber side grips.

    Bewerken

  6. Mad Catz Street Fighter IV FightPad Circuit Board Replacement, RS-DP-LS Switch: stap 5, afbeelding 1 van 2 Mad Catz Street Fighter IV FightPad Circuit Board Replacement, RS-DP-LS Switch: stap 5, afbeelding 2 van 2

    • Locate RS-DP-LS switch.

    • Pull upwards on the switch to remove it.

    Bewerken

  7. Mad Catz Street Fighter IV FightPad Circuit Board Replacement, Circuit Board: stap 6, afbeelding 1 van 1

    • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    Bewerken

  8. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 7, afbeelding 1 van 3 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 7, afbeelding 2 van 3 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: stap 7, afbeelding 3 van 3

    • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

    • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

    • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 8 andere bijdragers

Jefferson Hsu

Lid sinds: 09/18/12

411 Reputatie

3 handleidingen geschreven

Medailles: 9

+6 andere badges

Team

Cal Poly, Team 1-7, Propen Fall 2012 Lid van Cal Poly, Team 1-7, Propen Fall 2012

CPSU-PROPEN-F12S1G7

4 Leden

14 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 0

Altijd: 2,043