Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

MacBook Pro 15" Unibody Mid 2009 Optical Drive Replacement

Geschreven door: Andrew Bookholt (en 3 andere bijdragers)
  • Reacties: 10
  • Favorieten: 1

Moeilijkheid

Gemiddeld

Stappen

9

Tijd vereist

Stel een tijd voor??

Secties

1

Markeringen

1

Prerequisite Only

Alleen vereisten

Houd er rekening mee dat dit slechts een vereiste handleiding is voor andere handleidingen.

Inleiding

This guide is an internal prerequisite and should remain unpublished.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Apple sticks a small strip of clear plastic with adhesive applied to one side to the logic board behind the camera cable connector to keep it in its socket. When moving it out of the way, be sure not to break any surface-mount components off the logic board.

    • Apple sticks a small strip of clear plastic with adhesive applied to one side to the logic board behind the camera cable connector to keep it in its socket. When moving it out of the way, be sure not to break any surface-mount components off the logic board.

    • Hold the end of the cable retainer down with one finger while you use the tip of a spudger to slightly lift the other end and rotate it away from the camera cable connector.

    Bewerken

  2. Disconnect the camera cable by pulling the male end straight away from its socket. Pull the connector parallel to the face of the logic board, not straight up.

    • Disconnect the camera cable by pulling the male end straight away from its socket.

    • Pull the connector parallel to the face of the logic board, not straight up.

    Bewerken

  3. Peel the camera cable off the adhesive securing it to the optical drive.

    • Peel the camera cable off the adhesive securing it to the optical drive.

    Bewerken

  4. iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    Nu winkelen

    iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    Nu winkelen

  5. This step is only required if you have an anti-glare display. If you have a glossy display, skip this step. Disconnect the Bluetooth cable by pulling the male end straight away from its socket.

    • This step is only required if you have an anti-glare display. If you have a glossy display, skip this step.

    • Disconnect the Bluetooth cable by pulling the male end straight away from its socket.

    • Pull the connector parallel to the face of the logic board, not straight up.

    • Use the flat end of a spudger to pry the Bluetooth antenna cable from its socket on the board.

    Bewerken

  6. This step is only required if you have an anti-glare display. Remove the two 8 mm Phillips screws securing the Bluetooth/camera cable retainer to the upper case.

    • This step is only required if you have an anti-glare display.

    • Remove the two 8 mm Phillips screws securing the Bluetooth/camera cable retainer to the upper case.

    • One of the screws may remain captive in the Bluetooth/camera cable ground loop. If replacing the display, be sure to transfer this screw to the new unit.

    • Lift the Bluetooth board/cable retainer assembly out of the upper case.

    Bewerken

  7. Use a spudger to pry the optical drive connector straight up off the logic board.

    • Use a spudger to pry the optical drive connector straight up off the logic board.

    Bewerken

  8. Remove the single 3.5 mm Phillips screw securing the inner side of the optical drive to the upper case.

    • Remove the single 3.5 mm Phillips screw securing the inner side of the optical drive to the upper case.

    Bewerken

  9. Remove the two 3.5 mm Phillips screws securing the outer side of the optical drive to the upper case.

    • Remove the two 3.5 mm Phillips screws securing the outer side of the optical drive to the upper case.

    Bewerken

  10. Lift the optical drive from its left edge and pull it out of the upper case.

    • Lift the optical drive from its left edge and pull it out of the upper case.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

0 Opmerkingen

Een opmerking toevoegen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 0

Altijd: 684