Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.
Wat je nodig hebt
-
Deze stap is niet vertaald. Help het te vertalen
-
Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the three identical Phillips screws from the memory door.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following 6 screws:
-
Two 10 mm T6 Torx screws on either side of the RAM slot.
-
Four 14.5 mm Phillips screws along the hinge.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the four 3.2 mm Phillips screws on the port side of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case (there are some hidden plastic clips that need to be clicked off).
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
-
Remove the upper case.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the three antenna cables attached to the Airport Extreme card.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Deroute the Airport antenna cables from their channel in the left speaker.
-
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the inverter cable from the logic board by placing a spudger beneath the cable and lifting up.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the display data cable from the logic board by pulling sideways.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the silver T6 Torx securing the ground loop in the display data cable to the casing.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Support the display with one hand while removing the following 3 screws:
-
Two 9.5 mm silver T6 Torx screws with threads on only part of the shaft on the inside of the display hinges.
-
One 9.5 mm silver T6 Torx screw with threads on the entire shaft on the outside of the left hinge.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Grasp the display assembly on both sides and lift it up and out of the computer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two 5 mm Phillips screws from the lower left and right corners of the display (two screws total).
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
-
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
-
Work along the left edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
-
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
-
Work along the right edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Insert the flat end of a spudger between the front bezel and the plastic strip attached to the rear bezel near the screw holes at the bottom corners of the display.
-
Rotate your spudger toward the rear bezel to separate it from the front bezel.
-
If necessary, enlarge the gap between the lower edge of the rear bezel and the clutch cover until the two components are completely separated.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the rear bezel by its bottom edge and rotate it away from the display assembly to separate the top edge.
-
Remove the rear display bezel from the display assembly.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully lift the inverter board out of the clutch cover.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the LCD backlight from the inverter by pulling its connector away from the inverter board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Disconnect the inverter cable by pulling its connector away from the socket on the inverter.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the pieces of yellow kapton tape from the bottom left corner of the display.
-
Peel the three green antenna ground straps off the copper tape along the bottom edge of the LCD.
-
Remove the piece of tape securing the camera cable to the LCD.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the pieces of tape covering the display data cable and camera cable connectors.
-
Carefully peel the camera cable off the foam tape along the top edge of the LCD.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Gently pull the camera cable away from its socket on the camera board.
-
Pull the display data cable connector away from its socket on the LCD.
-
Pull both cables parallel to the face of the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
If you have a Core Duo machine, refer to picture 1 and remove three Phillips screws connecting the clutch assembly to the lower edge of the front display bezel near the display data cable.
-
If you have a Core 2 Duo Model A1211 machine, refer to picture 2 and remove two Phillips screws connecting the clutch assembly to the lower edge of the front display bezel near the display data cable.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the small Phillips screw from behind the display data cable.
-
Remove the small rectangular steel bracket by sliding it away from the right clutch hinge.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove three Phillips screws attaching the clutch assembly to the lower edge of the front display bezel.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Push the open edge of the clutch cover away from the left clutch hinge to pop it off the clips attaching the two parts.
-
Remove the clutch assembly from the front display bezel.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
De-route the inverter/camera cable from the left clutch hinge and remove it from the display.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the four T6 Torx screws securing the left clutch hinge to the front display bezel.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the left clutch hinge from the front display bezel.
-
Annuleren: ik heb deze handleiding niet afgemaakt.
Één andere persoon heeft deze handleiding voltooid.