Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.
Wat je nodig hebt
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two 2.1 mm T5 Torx screws securing the I/O board cable bracket to the logic board.
-
Remove the I/O board cable bracket.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the flat end of a spudger to pop the I/O board connector straight up off its socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the logic board end of the I/O board cable straight up to bend it out of the way.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the tip of a spudger to lift the right speaker connector straight up out of its socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
With the tip of a spudger, push on either side of the I/O board connector to walk it out of its socket on the logic board.
Use your fingernails to pinch the sides of the clip inwards to release the connector. I couldn’t walk it out either, both sides needed to be pushed in simultaneously to pull it out of the socket.
Do not pull from the cables end. you will risk separating thin cables from connector head. Use spudger tip to push it out.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the flat end of a spudger to disconnect the keyboard backlight cable and bend it up out of the way of the logic board.
-
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Grab the black plastic tab to flip the display cable connector open and pull it straight out of its socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully pull the DC-In board connector straight out of its socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Wedge the flat end of a spudger under the left speaker cable near the connector and lift it straight up out of its socket and fold it out of the way.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the tip of a spudger to flip the retaining tab on the microphone cable ZIF connector.
-
Pull the microphone cable out of its socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the tip of a spudger to flip the retaining tab on the ZIF connector.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Pull the keyboard cable straight out of its ZIF socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the tip of a spudger to flip the retaining tab on the ZIF connector.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Pull the trackpad ribbon cable straight out of its socket on the logic board.
I didn’t pay enough attention when I pulled the ribbon cable out, so trying to figure out how to reattach it was quite challenging for me. After searching unsuccessfully for videos/instructions on how to reattach, I finally figured out that the ribbon cable goes UNDER the black plastic part of the socket (closest to the ribbon), and then you push the little tab down to hold it in place. Hope this helps others who are struggling with this part. Otherwise, this was an amazing tutorial, and saved my macbook…
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the five 3.5 mm T5 Torx screws securing the logic board to the upper case.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift the processor end of the logic board up slightly and pull it toward the fan recess to free the ports from the edge of the upper case.
-
Remove the logic board.
-
Één opmerking
Thanks for the the instructions. I have a question that I couldn’t find on the answers forums. Is there any thermal paste or just general cooling system considerations when replacing the logic board?