Ga door naar hoofdinhoud

Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.

Wat je nodig hebt

  1. , Onderste behuizing: stap 1, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    Magnetic Project Mat
    $19.95
    Koop
    • Verwijder de volgende tien schroeven die de onderste behuizing aan de bovenste behuizing bevestigen:

    • Twee 2.3 mm lange P5 Pentalobe-schroeven

    • Acht 3.0 mm lange P5 Pentalobe-schroeven

    • Zorg dat je, tijdens deze reparatie, bijhoudt welke schroeven waar vandaan komen en zorg ervoor dat je ze op dezelfde plek terugschroeft om schade te voorkomen.

    If don’t have one of those neat project mats, then you can use small pieces of flattened blu-tack to hold the screws. If you arrange them in the shape of your mac book cover, and put the screws down methodically, you can get a one-to-one mapping of the screws to the correct screw holes.

    Toby Thurston - Antwoord

    Or you can use an ice tray where you put the screws and the parts in separate bays in the same order as they come in the instructions.

    timofej.se -

    This is great! I used a small magnetic white board, and wrote on it to identify the parts as I went. This whole process, from the fast shipment to the great instructions to the complete, high quality, tool kit has been great. I’m typing this comment on my resurrected laptop. Thank you! Sue

    Susan Greer - Antwoord

    It would be a good idea if people recorded in the comments which screws go where so that, if someone lost their screw positions, they could recover them from the comments.

    Raymond Shpeley - Antwoord

  2. : stap 2, afbeelding 1 van 1
    • Zorg dat je je vinger tussen de bovenste en de onderste behuizing wringt.

    • Trek de onderste behuizing vervolgens rustig weg van de bovenste behuizing.

    • Verwijder de onderste behuizing en leg deze weg.

  3. : stap 3, afbeelding 1 van 3 : stap 3, afbeelding 2 van 3 : stap 3, afbeelding 3 van 3
    • De onderste behuizing is in het midden met twee plastic klemmen verbonden met de bovenste behuizing.

    • Duw het midden van de onderste behuizing, tijdens het weer in elkaar zetten van je toestel, rustig naar beneden om de twee plastic klemmen weer aan elkaar te verbinden.

  4. , Batterijaansluiting: stap 4, afbeelding 1 van 1
    • Verwijder de plastic bescherming die aan het contactbord van de batterij is bevestigd.

    The replacement cover doesn't seem to have the formed pads attached. I re-installed the original.

    Adrien - Antwoord

  5. : stap 5, afbeelding 1 van 1
    • Verwijder de volgende schroeven die het connectorbord van de batterij aan het logic board bevestigen:

    • Twee 2.8 mm lange T6 Torx-schroeven

    • Eén 7.0 mm lange T6 Torx geschouderde schroef

  6. : stap 6, afbeelding 1 van 2 : stap 6, afbeelding 2 van 2
    • Gebruik een pincet om de kleine plastic bescherming bij de rechter onderhoek van het connectorbord van de batterij te verwijderen.

    Is adhered to screw beneath, so lift firmly and slowly.

    Andrew - Antwoord

    when doing this with metal tweezers as instructed in the video, it was difficult to get off and apparently while i was trying to do it, the tweezers went too far under and i believe made contact with the screw underneath? there was a zzz noise, an orange flicker and a little stream of smoke that came out. i freaked out and put everything back together to see if the laptop even still worked, it turned on and everything but died right away (i drained it before doing the repair anyway, so i was surprised it turned on at all).

    i finished the battery repair and did several other things while in there. i have charged it all the way as recommended and will use it later on to see how everything is, im hoping that it’s a okay, but could someone explain to me what happened and the possible consequences?

    Kait D - Antwoord

  7. : stap 7, afbeelding 1 van 1
    • Verwijder de breedkop 6.4 mm lange T6 Torx-schroef die de batterijaansluiting aan de logic boardmodule bevestigt.

    When reinstalling, be careful that the board lines up correctly and is completely seated in order for this screw to thread properly.

    Adrien - Antwoord

  8. : stap 8, afbeelding 1 van 2 : stap 8, afbeelding 2 van 2
    • Til het connectorbord van de batterij voorzichtig omhoog en weg van het logic board.

    • Het wordt aangeraden om de batterijkabels lichtjes uit de weg te duwen om het board zodat het niet in de weg komt te zitten.

    • Haal het bord en de kabels echter niet te ver weg, aangezien je hiermee schade riskeert.

  9. Deze stap is niet vertaald. Help het te vertalen

    : stap 9, afbeelding 1 van 1
    • Remove the single 2.7 mm T5 Torx screw securing the AirPort board to the I/O board.

  10. Deze stap is niet vertaald. Help het te vertalen

    : stap 10, afbeelding 1 van 3 : stap 10, afbeelding 2 van 3 : stap 10, afbeelding 3 van 3
    • Use the flat end of a spudger to pry and disconnect the three antenna cable connectors from the AirPort board.

    • The three cables are coded with black sleeves of different lengths. During reassembly:

    • Connect the long-sleeved cable to the center socket.

    • The short-sleeved cable connects next to the screw.

    • The remaining cable has no sleeve, and connects in the last empty socket, next to the fan.

  11. Deze stap is niet vertaald. Help het te vertalen

    : stap 11, afbeelding 1 van 2 : stap 11, afbeelding 2 van 2
    • Move the antenna cables aside, clear of the AirPort board.

  12. Deze stap is niet vertaald. Help het te vertalen

    : stap 12, afbeelding 1 van 2 : stap 12, afbeelding 2 van 2
    • Wedge a plastic opening tool between the AirPort board (side nearest the I/O ports) and the I/O board.

    • Gently pry the AirPort board upwards, but do not remove it.

    • Only lift the AirPort board as much as is necessary to get a grip on it. Lifting it too high above the I/O board may damage the board or the socket.

  13. Deze stap is niet vertaald. Help het te vertalen

    : stap 13, afbeelding 1 van 2 : stap 13, afbeelding 2 van 2
    • Pull the AirPort board straight out of its socket on the I/O board.

  14. Deze stap is niet vertaald. Help het te vertalen

    : stap 14, afbeelding 1 van 1
    • AirPort board remains.

Eindstreep

17 andere personen hebben deze handleiding voltooid.

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 2

Afgelopen 7 dagen: 12

Afgelopen 30 dagen: 48

Altijd: 16,327