Inleiding

Steps to remove LG VX8550 slider mechanism

Slide the battery release up.
  • Slide the battery release up.

Voeg opmerking toe

Remove the battery by lifting away from the case.
  • Remove the battery by lifting away from the case.

Voeg opmerking toe

Remove the 2 screw covers next to the rear speaker with a Push Pin.
  • Remove the 2 screw covers next to the rear speaker with a Push Pin.

Voeg opmerking toe

Remove the 4 cover screws with a Philips #00 screwdriver.
  • Remove the 4 cover screws with a Philips #00 screwdriver.

Voeg opmerking toe

Use the iPod opening tool to pry off the back casing.
  • Use the iPod opening tool to pry off the back casing.

Voeg opmerking toe

Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.
  • Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.

Voeg opmerking toe

Separate the casing halves.
  • Separate the casing halves.

  • Be sure to keep track of the side buttons as they fall out.

Voeg opmerking toe

Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.
  • Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.

Voeg opmerking toe

Carefully lift up on the motherboard to see the ribbon cables underneath.
  • Carefully lift up on the motherboard to see the ribbon cables underneath.

  • Use the spudger to carefully disconnect the ribbon cable from the motherboard.

Voeg opmerking toe

Remove the motherboard from the front casing by lifting straight up.
  • Remove the motherboard from the front casing by lifting straight up.

Voeg opmerking toe

Lay the phone with the screen facedown.
  • Lay the phone with the screen facedown.

  • The 6 slider screws are visible.

Voeg opmerking toe

Peel back but don't remove the blue tape to access the 2 center screws.
  • Peel back but don't remove the blue tape to access the 2 center screws.

  • Remove the 6 slider screws with the Phillips #00 screwdriver.

Voeg opmerking toe

Lift the keypad housing away from the slider.
  • Lift the keypad housing away from the slider.

Voeg opmerking toe

Remove the 2 screw covers next to the speaker with a push pin next to the camera.
  • Remove the 2 screw covers next to the speaker with a push pin next to the camera.

Voeg opmerking toe

Remove the 6 screws with a Phillips #00 Screwdriver.
  • Remove the 6 screws with a Phillips #00 Screwdriver.

Voeg opmerking toe

Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.
  • Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.

Voeg opmerking toe

Carefully lift the slider mechanism to see the ribbon cables underneath.
  • Carefully lift the slider mechanism to see the ribbon cables underneath.

Voeg opmerking toe

Slide ribbon cable through the slider mechanism.
  • Slide ribbon cable through the slider mechanism.

Voeg opmerking toe

Separate the two halves.
  • Separate the two halves.

Voeg opmerking toe

With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.
  • With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.

  • Remove the 8 screws.

Voeg opmerking toe

Remove slider mechanism.  Now is a good time to clean slider mechanism if sticky.
  • Remove slider mechanism. Now is a good time to clean slider mechanism if sticky.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Nathan Jones

Lid sinds: 10-04-10

83 reputatie

20 handleidingen geschreven

Team

Cal Poly, Team 34-55, Forte Spring 2010 Lid van Cal Poly, Team 34-55, Forte Spring 2010

CPSU-FORTE-S10S34G55

5 Leden

20 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 0

Altijd: 2,993