Repareer je spullen Gemeenschap Winkel

Kenwood DNX571HD LCD Touch Screen Replacement

Inleiding

If your screen has been damaged and needs to be replaced, this guide will provide the steps to remove the old screen and replace it with a new one.

Wat je nodig hebt

  1. Kenwood DNX571HD LCD Touch Screen Replacement, LCD Touch Screen: stap 1, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement, LCD Touch Screen: stap 1, afbeelding 2 van 2

    • Turn off the stereo and remove from the vehicle before starting.

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Vertaal

  2. Kenwood DNX571HD LCD Touch Screen Replacement: stap 2, afbeelding 1 van 3 Kenwood DNX571HD LCD Touch Screen Replacement: stap 2, afbeelding 2 van 3 Kenwood DNX571HD LCD Touch Screen Replacement: stap 2, afbeelding 3 van 3

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Vertaal

  3. Kenwood DNX571HD LCD Touch Screen Replacement: stap 3, afbeelding 1 van 1

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Vertaal

  4. Kenwood DNX571HD LCD Touch Screen Replacement: stap 4, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 4, afbeelding 2 van 2

    • Flip up the black clasp with the spudger to disconnect the small white ribbon cable from the main board.

    Vertaal

  5. Kenwood DNX571HD LCD Touch Screen Replacement: stap 5, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 5, afbeelding 2 van 2

    • Flip up the black clasp with the spudger to disconnect the large white ribbon cable from the main board.

    Vertaal

  7. Kenwood DNX571HD LCD Touch Screen Replacement: stap 6, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 6, afbeelding 2 van 2

    • Flip up the black clasp with the spudger to disconnect the small white ribbon cable from the vertical board.

    • Carefully pull the ribbon from the clasp with the spudger.

    Vertaal

  8. Kenwood DNX571HD LCD Touch Screen Replacement: stap 7, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 7, afbeelding 2 van 2

    • Flip up the black clasp with the spudger to disconnect the large orange ribbon cable from the main board.

    • Carefully pull the ribbon from the clasp with the spudger.

    Vertaal

  9. Kenwood DNX571HD LCD Touch Screen Replacement: stap 8, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 8, afbeelding 2 van 2

    • Push out the black clasp with the spudger to disconnect the small orange ribbon cable from the main board.

    • Gently push the ribbon out of the clasp with the spudger.

    Vertaal

  10. Kenwood DNX571HD LCD Touch Screen Replacement: stap 9, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 9, afbeelding 2 van 2

    • Using a pair of tweezers, gently pull up on the connector for the power cable to disconnect it from the main board.

    Vertaal

  11. Kenwood DNX571HD LCD Touch Screen Replacement: stap 10, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 10, afbeelding 2 van 2

    • Unscrew the two 4mm screws holding down the board that is standing vertically with a Phillips #1 screwdriver.

    • Pull up on the board to remove it.

    Vertaal

  12. Kenwood DNX571HD LCD Touch Screen Replacement: stap 11, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 11, afbeelding 2 van 2

    • Unscrew the four 5.5mm screws with a JIS #00 screwdriver.

    • Unscrew the 4mm screw with a Phillips #1 screwdriver.

    • Remove the disconnected circuit board.

    Vertaal

  13. Kenwood DNX571HD LCD Touch Screen Replacement: stap 12, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 12, afbeelding 2 van 2

    • Unscrew the four 4mm screws on the main board with a Phillips #1 screwdriver.

    • Gently lift the board out of the casing.

    • Unscrew the 5.5mm screw on the metal plate with a JIS #00 screwdriver.

    Vertaal

  14. Kenwood DNX571HD LCD Touch Screen Replacement: stap 13, afbeelding 1 van 1

    • Carefully remove the tape attaching the power cable to the metal plate.

    Vertaal

  15. Kenwood DNX571HD LCD Touch Screen Replacement: stap 14, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 14, afbeelding 2 van 2

    • Use the spudger to unhook the metal tabs and detach the metal plate from the plastic housing.

    • Place the spudger between the metal tab and the plastic case and gently lift the spudger away from the case.

    Vertaal

  16. Kenwood DNX571HD LCD Touch Screen Replacement: stap 15, afbeelding 1 van 2 Kenwood DNX571HD LCD Touch Screen Replacement: stap 15, afbeelding 2 van 2

    • Gently press the front of the screen to detach it from the plastic housing.

    • When removing the screen, gently flex out the plastic housing to help get the display past the plastic latch.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

4 andere personen hebben deze handleiding voltooid.

Auteur

met 5 andere bijdragers

Wendy Zaballos

Lid sinds: 09/17/18

952 Reputatie

6 handleidingen geschreven

Medailles: 8

+5 andere badges

Team

Washington State, Team S1-G1, Hope Fall 2018 Lid van Washington State, Team S1-G1, Hope Fall 2018

WSU-HOPE-F18S1G1

4 Leden

6 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 18

Afgelopen 30 dagen: 72

Altijd: 9,210