Ga door naar hoofdinhoud

Inleiding

You will need to research online for replacement batteries of the same dimensions, 3.7 volts, 330mAh (or greater) and with wire leads. The replacement consists of desoldering the old batteries and soldering the new ones to the motherboard. This replacement guide will give you the confidence to do it yourself.

  1. Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws. Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws.
    • Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws.

  2. Remove the six 20 mm T6 screws from the bottom of the device.
    • Remove the six 20 mm T6 screws from the bottom of the device.

    Remove the screws using T6 Torx screwdriver.

    Taha Asad - Antwoord

  3. Remove the back plate and the grey foam underneath. Remove the back plate and the grey foam underneath.
    • Remove the back plate and the grey foam underneath.

  4. Use a small, pointed metal spudger to  release the plastic tabs connecting the faceplate to the bottom of the speaker. A small cable connects the faceplate to the device. Carefully disconnect the cable before fully opening  the device. Slowly flip the device open like a clam shell.
    • Use a small, pointed metal spudger to release the plastic tabs connecting the faceplate to the bottom of the speaker.

    • A small cable connects the faceplate to the device. Carefully disconnect the cable before fully opening the device.

    • Slowly flip the device open like a clam shell.

    • There are several wires soldered to the motherboard that prevent the faceplate from detaching completely.

    The hooks on the plastic tabs point inwards. You can see the counterpart of a hook on the 2nd picture on the left of the battery.

    I released the hooks by pushing the plastic pads outwards, gently pulling a flat-head screwdriver towards the center. It is necessary to pull the screwdriver ca. 3mm back from the maximum possible depth (otherwise you would push the counterpart outwards, instead of the plastic pad).

    Franz - Antwoord

  5. Once you have carefully separated the bottom case from the top case, locate the two batteries attached to the motherboard. Notice that each battery has two wires, one red and the other black, soldered to the board. Make a careful note of which is soldered to which pad.
    • Once you have carefully separated the bottom case from the top case, locate the two batteries attached to the motherboard.

    • Notice that each battery has two wires, one red and the other black, soldered to the board. Make a careful note of which is soldered to which pad.

    • Desolder the battery connections using the heated soldering iron.

    • You can find soldering tips in the How To Solder and Desolder Connections guide.

  6. The battery is glued to the motherboard. Take care not to damage it in any way with excessive force in removing it.
    • The battery is glued to the motherboard. Take care not to damage it in any way with excessive force in removing it.

    • Carefully pry the battery away from the motherboard using a plastic opening tool. The glue gives very slowly under constant pressure and cannot be hurried. As the battery starts to lift you can insert the prying tool further as you continue to lift the battery.

    • The adhesive may still have sufficient stickiness to hold the new batteries, but if not, replace it with doule sided tape.

    • Solder the wires of the new batteries to the board, making sure that the red and black do to the correct pads.

Conclusie

To reassemble your device, follow these instructions in reverse order.

13 andere personen hebben deze handleiding voltooid.

Edgar Tavares

Lid sinds: 16-02-16

341 Reputatie

1 Handleiding geschreven

Team

IUPUI, Team 2-3, Harley Spring 2016 Lid van IUPUI, Team 2-3, Harley Spring 2016

IUPUI-HARLEY-S16S2G3

4 Leden

4 handleidingen geschreven

Thanks pal!

Freezing the headset in an airtight bag for 24 hours worked.

Best wishes,

Ronny

Norway

Ronny - Antwoord

Very precisely described steps, super well written - excellent job Ed, thanks

Rafael Benitez - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 19

Afgelopen 7 dagen: 84

Afgelopen 30 dagen: 353

Altijd: 15,284