Ga door naar hoofdinhoud

Iomega Z100S2 Disk Reader Replacement

Wat je nodig hebt

  1. Iomega Z100S2 Disk Reader Replacement, Case: stap 1, afbeelding 1 van 2 Iomega Z100S2 Disk Reader Replacement, Case: stap 1, afbeelding 2 van 2
    • Push in the plastic tab that can be seen through cracks in the front left corner using a spudger.

  2. Iomega Z100S2 Disk Reader Replacement: stap 2, afbeelding 1 van 1
    • Move down the same side and push in the plastic tab.

  3. Iomega Z100S2 Disk Reader Replacement: stap 3, afbeelding 1 van 1
    • Move to the front right side and once again push in the plastic tab.

    • There is not a fourth tab to push in after this one.

  4. Iomega Z100S2 Disk Reader Replacement: stap 4, afbeelding 1 van 2 Iomega Z100S2 Disk Reader Replacement: stap 4, afbeelding 2 van 2
    • Grab the cover by the front side and pull upwards.

    • You might encounter some resistance. Pull firmly, but don't yank it.

  5. Iomega Z100S2 Disk Reader Replacement: stap 5, afbeelding 1 van 2 Iomega Z100S2 Disk Reader Replacement: stap 5, afbeelding 2 van 2
    • Tilt the front case down until the pegs detach from the bottom of the case.

    • Lift up and outward.

    • The motherboard will be loose at this point.

  6. Iomega Z100S2 Disk Reader Replacement, Disk Reader: stap 6, afbeelding 1 van 2 Iomega Z100S2 Disk Reader Replacement, Disk Reader: stap 6, afbeelding 2 van 2
    • Unhook the two springs from the front plastic hooks.

    • The black side rails of the reader should easily slide forward and off.

  7. Iomega Z100S2 Disk Reader Replacement: stap 7, afbeelding 1 van 1
    • There is a white tab connected to the motherboard. Pull it upward by gently rocking it back and forth.

    • The tab does not come completely out, it only slides up slightly, so don't rip it out!

  8. Iomega Z100S2 Disk Reader Replacement: stap 8, afbeelding 1 van 2 Iomega Z100S2 Disk Reader Replacement: stap 8, afbeelding 2 van 2
    • Grab the reader by its sides and gently pull it upward.

    • There are two wires still connected to the bottom of the reader that haven't been detached.

  9. Iomega Z100S2 Disk Reader Replacement: stap 9, afbeelding 1 van 1
    • Disconnect the white wires by using tweezers to gently pull the bottom connector toward you.

  10. Iomega Z100S2 Disk Reader Replacement: stap 10, afbeelding 1 van 2 Iomega Z100S2 Disk Reader Replacement: stap 10, afbeelding 2 van 2
    • Disconnect the thin ribbon wire by using tweezers to gently pull the connector at the bottom toward you.

  11. Iomega Z100S2 Disk Reader Replacement: stap 11, afbeelding 1 van 1
    • Lift the reader up and out from the device.

Conclusie

To reassemble your device, follow these instructions in reverse order.

5 andere personen hebben deze handleiding voltooid.

Ezery Kennedy

Lid sinds: 10/05/10

288 Reputatie

2 handleidingen geschreven

Team

Cal Poly, Team 7-53, Amido Fall 2010 Lid van Cal Poly, Team 7-53, Amido Fall 2010

CPSU-AMIDO-F10S7G53

4 Leden

6 handleidingen geschreven

2 opmerkingen

Great guide exactly what I was looking for.

Jim Schmidt - Antwoord

Zip disks were awesome, and they still are they fit that niche between needing something small in capacity but not large enough for a USB flash drive.

Trevor Rawlinson - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 5

Afgelopen 30 dagen: 25

Altijd: 6,068