Repareer je spullen Gemeenschap Winkel

Insignia Flex 8 Speakers Replacement

Wat je nodig hebt

  1. Insignia Flex 8 Speakers Replacement, Circuit Board: stap 1, afbeelding 1 van 1

    • Turn off the power to your tablet to avoid injury.

    • Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.

    • Hold down the power button for five seconds until the tablet powers down.

    Bewerken

  2. Insignia Flex 8 Speakers Replacement: stap 2, afbeelding 1 van 2 Insignia Flex 8 Speakers Replacement: stap 2, afbeelding 2 van 2

    • Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.

    • You may need to use a spudger to initially create separation between the screen and the casing.

    • Run this object around the perimeter of the tablet until there is separation between the casing and the screen.

    • Remove the back casing and set aside.

    Bewerken

  3. Insignia Flex 8 Speakers Replacement: stap 3, afbeelding 1 van 2 Insignia Flex 8 Speakers Replacement: stap 3, afbeelding 2 van 2

    • Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

    Bewerken

  4. Insignia Flex 8 Speakers Replacement: stap 4, afbeelding 1 van 3 Insignia Flex 8 Speakers Replacement: stap 4, afbeelding 2 van 3 Insignia Flex 8 Speakers Replacement: stap 4, afbeelding 3 van 3

    • To remove the camera ribbon cable, lift the flap using a spudger.

    • Pull the ribbon directly back to release it.

    Bewerken

  5. Insignia Flex 8 Speakers Replacement: stap 5, afbeelding 1 van 3 Insignia Flex 8 Speakers Replacement: stap 5, afbeelding 2 van 3 Insignia Flex 8 Speakers Replacement: stap 5, afbeelding 3 van 3

    • Remove the second ribbon cable by prying up the black flap using a spudger.

    • Pull the ribbon cable horizontally directly away from the battery.

    Bewerken

  7. Insignia Flex 8 Speakers Replacement: stap 6, afbeelding 1 van 3 Insignia Flex 8 Speakers Replacement: stap 6, afbeelding 2 van 3 Insignia Flex 8 Speakers Replacement: stap 6, afbeelding 3 van 3

    • Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.

    • Pull the ribbon horizontally directly away from the battery.

    Bewerken

  8. Insignia Flex 8 Speakers Replacement: stap 7, afbeelding 1 van 2 Insignia Flex 8 Speakers Replacement: stap 7, afbeelding 2 van 2

    • Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

    Bewerken

  9. Insignia Flex 8 Speakers Replacement: stap 8, afbeelding 1 van 2 Insignia Flex 8 Speakers Replacement: stap 8, afbeelding 2 van 2

    • Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.

    • Lift up the circuit board.

    Bewerken

  10. Insignia Flex 8 Speakers Replacement: stap 9, afbeelding 1 van 1

    • Unscrew the final two screws that were underneath the circuit board.

    • These screws are near the charging port and USB adapter.

    • These screws are also 3.75mm and can be interchanged with the second set of screws only.

    Bewerken

  11. Insignia Flex 8 Speakers Replacement: stap 10, afbeelding 1 van 1

    • Lift the circuit board and black internal mounting piece away from the screen.

    • Set the circuit board aside.

    • Be careful of the soldered antenna as you separate the pieces.

    • Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

    Bewerken

  12. Insignia Flex 8 Speakers Replacement, Speakers: stap 11, afbeelding 1 van 2 Insignia Flex 8 Speakers Replacement, Speakers: stap 11, afbeelding 2 van 2

    • Looking at the front of the speaker, peel back the rectangular cover to expose the speaker.

    Bewerken

  13. Insignia Flex 8 Speakers Replacement: stap 12, afbeelding 1 van 1

    • Desolder the connections from the circuit board

    • Do not heat up the surrounding components on the circuit board.

    Bewerken

  14. Insignia Flex 8 Speakers Replacement: stap 13, afbeelding 1 van 1

    • Turn the black internal mounting piece over to access the back of the speaker.

    • Use a spudger to lift the cover open.

    • The cover is attached with a plastic solder, be careful not to break the cover.

    Bewerken

  15. Insignia Flex 8 Speakers Replacement: stap 14, afbeelding 1 van 1

    • Pull the speaker out of its housing.

    • Repeat these steps for the other speaker.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 1 andere bijdrager

Tyler Tyrrell

Lid sinds: 03/11/15

890 Reputatie

4 handleidingen geschreven

Medailles: 17

+14 andere badges

Team

Colorado Springs, Team 5-5, Panko Spring 2015 Lid van Colorado Springs, Team 5-5, Panko Spring 2015

UCCS-PANKO-S15S5G5

3 Leden

12 handleidingen geschreven

Één opmerking

coooooooooooooooooooooooooooooooooooooooooooooooooooool

Angel Nicholas - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 4

Altijd: 438