Repareer je spullen Gemeenschap Winkel

Insignia Flex 10.1 NS-P10W8100 Camera Replacement

Inleiding

Although there are no known hazards with removing the camera, be careful not to damage any small components or permanently damage any connectors.

Wat je nodig hebt

  1. Insignia Flex 10.1 NS-P10W8100 Camera Replacement, Camera: stap 1, afbeelding 1 van 2 Insignia Flex 10.1 NS-P10W8100 Camera Replacement, Camera: stap 1, afbeelding 2 van 2

    • Carefully open the laptop and remove the keyboard by disconnecting it.

    • Place keyboard to the side as you will not need it.

    • Beware of plastic clips on the side of the device.

    Bewerken

  2. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 2, afbeelding 1 van 2 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 2, afbeelding 2 van 2

    • Lay the screen flat on its surface and use the iFixit opening tool to remove the cover by gently prying the back cover from the screen.

    • Apply the opening tool to each side to help pry the back cover evenly.

    • Apply the opening tool to each side which will help pry the back cover evenly.

    • Do not pry on the bottom side of the device. This is the side across from the camera.

    Bewerken

  4. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 3, afbeelding 1 van 1

    • Use your fingers and pry the back cover from the screen. You may need to wiggle the cover a bit to separate the pieces.

    • If the back cover does not come off work your fingers around the corners and slowly pry the cover off using your fingers.

    • Be careful with potential sharp edges and any exposed electrical components.

    Bewerken

  5. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 4, afbeelding 1 van 2 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 4, afbeelding 2 van 2

    • Carefully remove the yellow tape holding down the camera ribbon connector by pulling it upwards.

    • Remove the black tape holding down the camera ribbon connector which is attached to the motherboard.

    Bewerken

  6. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 5, afbeelding 1 van 2 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 5, afbeelding 2 van 2

    • Disconnect the zero insertion force (ZIF) connector by using your fingernail to flip the small locking flap.

    • Disconnect the cable by gently pulling it outward.

    Bewerken

  7. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 6, afbeelding 1 van 3 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 6, afbeelding 2 van 3 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: stap 6, afbeelding 3 van 3

    • Remove the camera by pulling it upward.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 0

Altijd: 187