Gather the necessary tools
  • Gather the necessary tools

    • 1--Soldering Iron

    • 2--Solder

    • 3--DB9 Enclosure. This one is being used here.

    • 4--RS232 to TTL/CMOS converter. alldav.com sells the one used here. Cisco does not recommend or endorse Alldav specifically.

    • 5--Cable w/RJ45 connector on one end Any type of cable with an 8P8C (RJ45) connector could used as long as pins 1,2,7 & 8 are connected. A standard RJ45 cable is being used here.

    • You will also need wire strippers and possibly a screwdriver (depending on which DB9 enclosure you are using).

Voeg opmerking toe

Prep the cable. Strip the sheathing from the wires that correspond to pins 1,2,7 & 8.
  • Prep the cable. Strip the sheathing from the wires that correspond to pins 1,2,7 & 8.

Voeg opmerking toe

Connect the RS232 to TTL/CMOS converter. Connect the RS232 to TTL/CMOS converter to the cable and solder the connections. Note: The colors used in the wiring diagram don't correspond to the color of the actual wires.
  • Connect the RS232 to TTL/CMOS converter. Connect the RS232 to TTL/CMOS converter to the cable and solder the connections. Note: The colors used in the wiring diagram don't correspond to the color of the actual wires.

Voeg opmerking toe

Mac RAM Kits
Versnel je Mac. Breid zijn geheugen uit.
Mac RAM Kits
Haal meer megabytes uit je Mac.
Install the Enclosure The EX90 console is now complete.  The subsequent steps will cover making a console connection.
  • Install the Enclosure The EX90 console is now complete. The subsequent steps will cover making a console connection.

Voeg opmerking toe

Make a Console Connection. Locate the Console Port. The EX90 console port is an 8P8C (RJ45) connection and is located on the bottom left corner of the unit.
  • Make a Console Connection. Locate the Console Port. The EX90 console port is an 8P8C (RJ45) connection and is located on the bottom left corner of the unit.

Voeg opmerking toe

Connect to the Console Port. Plug the 8P8C (RJ45) end into the console port.  You'll have to lean the unit forward to plug the cable in. It might be a little awkward to do alone. If someone else is available, ask for their assistance. As a last resort, lay the unit down. Ensure you have something soft (like a towel) to lay the unit on.
  • Connect to the Console Port. Plug the 8P8C (RJ45) end into the console port. You'll have to lean the unit forward to plug the cable in. It might be a little awkward to do alone. If someone else is available, ask for their assistance. As a last resort, lay the unit down. Ensure you have something soft (like a towel) to lay the unit on.

Voeg opmerking toe

Connect the DB9 to a USB serial adapter and connect to a laptop/PC.
  • Connect the DB9 to a USB serial adapter and connect to a laptop/PC.

Voeg opmerking toe

Configure a Terminal Emulator Session Configure your terminal emulator with the following parameters:
  • Configure a Terminal Emulator Session Configure your terminal emulator with the following parameters:

    • Baud=38400

    • Data bits=8

    • Parity=none

    • Stop bits=1

    • Flow Control=none

  • The example uses HyperTerminal for Windows; configuring your terminal emulator may vary slightly.

  • You should now be at a login prompt when you connect with the terminal emulator.

Voeg opmerking toe

Eindstreep

Één andere persoon heeft deze handleiding voltooid.

eric

Lid sinds: 17-05-12

211 Reputatie

1 Handleiding geschreven

Één commentaar

Thanks for this Amazing Blog. It is very informative and helpful for me.

<a href="http://pdfdumps.us/exam/220-801.html">Pass4sure 220-801 dumps</a>

ademarr - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 1

Afgelopen 7 Dagen: 11

Afgelopen 30 Dagen: 47

Altijd: 4,967