Ga door naar hoofdinhoud

Onderdelen

Geen onderdelen opgegeven.

  1. Deze stap is niet vertaald. Help het te vertalen

    Squeeze the calipers together, and remove the brake cable. Squeeze the calipers together, and remove the brake cable. Squeeze the calipers together, and remove the brake cable.
    • Squeeze the calipers together, and remove the brake cable.

  2. Deze stap is niet vertaald. Help het te vertalen

    Loosen the brake caliper bolt, and remove the brake caliper. Loosen the brake caliper bolt, and remove the brake caliper. Loosen the brake caliper bolt, and remove the brake caliper.
    • Loosen the brake caliper bolt, and remove the brake caliper.

  3. Deze stap is niet vertaald. Help het te vertalen

    Inspect the brake pad. If the pad has worn down past the “wear line”, then it needs to be replaced. Inspect the brake pad. If the pad has worn down past the “wear line”, then it needs to be replaced.
    • Inspect the brake pad. If the pad has worn down past the “wear line”, then it needs to be replaced.

  4. Deze stap is niet vertaald. Help het te vertalen

    Clean and lubricate the parts as necessary before reattaching the caliper arms. Bolt the caliper arms back on while making sure the the pin on the back side of the caliper arm lines back up with the one of the holes in the frame. Each side should be in the same hole. Bolt the caliper arms back on while making sure the the pin on the back side of the caliper arm lines back up with the one of the holes in the frame. Each side should be in the same hole.
    • Clean and lubricate the parts as necessary before reattaching the caliper arms.

    • Bolt the caliper arms back on while making sure the the pin on the back side of the caliper arm lines back up with the one of the holes in the frame. Each side should be in the same hole.

  5. Deze stap is niet vertaald. Help het te vertalen

    Reattach the brake cable to the calipers. Reattach the brake cable to the calipers.
    • Reattach the brake cable to the calipers.

  6. Deze stap is niet vertaald. Help het te vertalen

    Loosen the brake pad bolt. Loosen the brake pad bolt.
    • Loosen the brake pad bolt.

  7. Deze stap is niet vertaald. Help het te vertalen

    Get an ordinary piece of paper, and fold it twice over. Place the sheet of paper between the brake pad and the rim in the position shown.
    • Get an ordinary piece of paper, and fold it twice over.

    • Place the sheet of paper between the brake pad and the rim in the position shown.

    What's the reason of doing this? Is it to keep 1 or 2 mm gap between the pad and rim or to 'toe-in' the break bad?

    Seamuzzaman Nahid - Antwoord

    Helps to prevent brake chatter by feathering in the pads to the rim.

    R I - Antwoord

    Is this some kind of spacer? I saw other (video) using credit card.

    Edwin Icogo - Antwoord

  8. Deze stap is niet vertaald. Help het te vertalen

    Align the brake pad so that it is flush with the rim, with no part touching the rubber of the tire. Have somebody clamp down very tightly on the brakes. Tighten the brake pad bolt in place.
    • Align the brake pad so that it is flush with the rim, with no part touching the rubber of the tire.

    • Have somebody clamp down very tightly on the brakes.

    • Tighten the brake pad bolt in place.

    The brake lever could also be held down with a cable tie, velcro strap, or a strong elastic band

    R I - Antwoord

    An old toe clip strap works also

    John Pesackis - Antwoord

    What happened to the folded paper?

    Edwin Icogo - Antwoord

    Ok ok I saw it in 3rd pics. :)

    Edwin Icogo -

  9. Deze stap is niet vertaald. Help het te vertalen

    Tighten/loosen the tension adjustment screws on each the caliper arm to adjust the resting distance of each brake pad, so that each pad is equally distant from the rim. Tightening the screw will shift the caliper outward from the bike, loosening it will shift it inward. Tighten/loosen the brake adjuster on the handle bars such that when you clamp down on the brakes, the brake lever stops before hitting the handle bar. This will set the distance between the brake pads and the rim. Tighten the lock nut on the brake adjuster to permanently set its position.
    • Tighten/loosen the tension adjustment screws on each the caliper arm to adjust the resting distance of each brake pad, so that each pad is equally distant from the rim. Tightening the screw will shift the caliper outward from the bike, loosening it will shift it inward.

    • Tighten/loosen the brake adjuster on the handle bars such that when you clamp down on the brakes, the brake lever stops before hitting the handle bar. This will set the distance between the brake pads and the rim.

    • Tighten the lock nut on the brake adjuster to permanently set its position.

    Very good!,Was wondering about some small details . This clered it out. Thx

    Tim Brumen - Antwoord

    I'll do this and will report back.

    Edwin Icogo - Antwoord

Eindstreep

47 andere personen hebben deze handleiding voltooid.

Travis Tonder

Lid sinds: 05-10-10

2.745 Reputatie

4 handleidingen geschreven

Team

Cal Poly, Team 5-13, Maness Fall 2010 Lid van Cal Poly, Team 5-13, Maness Fall 2010

CPSU-MANESS-F10S5G13

4 Leden

17 handleidingen geschreven

2 Opmerkingen

“what does it mean if the point is red???? “

I believe that is indicating that this step corresponds to an image which highlights a specific step. I saw this two times, in step 4 and step 9. For step 4, it shows the highlight in the second image and for step 9, the highlight is in the first image. It seems that the red bullet point is just to make it easier to map the step to the image.

Hope this helps

Tony - Antwoord

where did you get the brake arms from?

I am looking for full metal ones like that,

Ahmed Varnham - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 8

Afgelopen 7 dagen: 75

Afgelopen 30 dagen: 447

Altijd: 101,403