Repareer je spullen Gemeenschap Winkel

How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars

Inleiding

Binoculars are somewhat delicate, and when used outdoors in dynamic settings, they can sometimes sustain damage, which can knock the two sides out of alignment, culminating in double vision. Small changes in the positioning of the prisms can result in significant differences in the vision of the binoculars, and binocular manufacturers often hide the adjustment screws to discourage owners from attempting to repair them on their own. This guide will demonstrate how to find the adjustment screws on a pair of Barska 10x50 WA binoculars and adjust them to align the double vision.

Wat je nodig hebt

  1. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars, How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 1, afbeelding 1 van 1

    • Remove the main J0 head screw in the center of the binoculars, using the driver with the 4 mm bit and J0 attachment.

    Bewerken

  2. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 2, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 2, afbeelding 2 van 2

    • Remove the top piece and the washers held under the middle screw.

    Bewerken

  3. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 3, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 3, afbeelding 2 van 2

    • Pull the eyepieces off the binoculars.

    Bewerken

  4. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 4, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 4, afbeelding 2 van 2

    • Remove the two side J0 head screws.

    Bewerken

  5. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 5, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 5, afbeelding 2 van 2

    • Remove the four J0 head eyepiece screws.

    Bewerken

  7. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 6, afbeelding 1 van 1

    • Remove the two eyepiece plates.

    Bewerken

  8. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 7, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 7, afbeelding 2 van 2

    • Pry apart the rear rubber covering on each side to expose the two back prism adjustment screws.

    Bewerken

  9. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 8, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 8, afbeelding 2 van 2

    • Adjust the two 1.5 mm flat head prism screws by slightly turning the driver.

    • Note: Look through the binoculars after each turn, and if the vision is aligned, you can stop at this step. If adjusting these screws does not align the vision, proceed to Step 9.

    • DO NOT tighten the prism screws too much, or you will crack the prism and permanently destroy it. Repairing or replacing the prism is beyond the scope of this guide.

    Bewerken

  10. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 9, afbeelding 1 van 1

    • Unscrew the two front objective lenses by hand.

    Bewerken

  11. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 10, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 10, afbeelding 2 van 2

    • Unscrew the two J0 head front screws.

    Bewerken

  12. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 11, afbeelding 1 van 1

    • Remove the two front plates.

    Bewerken

  13. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 12, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 12, afbeelding 2 van 2

    • Peel back the front rubber coverings on both sides.

    Bewerken

  14. How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 13, afbeelding 1 van 2 How to Repair Double Vision on Barska 10x50 Wide-Angle Binoculars: stap 13, afbeelding 2 van 2

    • Adjust the two front 1.5 mm flat head prism screws with small turns.

    • Look through the binoculars after each adjustment to see if it is aligning the vision, and repeat the adjustments until it is repaired.

    • You may need to return to Step 8 to fine-tune the other set of screws. All four prism adjustment screws must be in their correct positions to produce the correct view through the binoculars.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

Auteur

met 4 andere bijdragers

James Silva

Lid sinds: 09/30/19

235 Reputatie

1 Handleiding geschreven

Medailles: 6

+3 andere badges

Team

CSU Fullerton, Team S1-G3, Bruce Fall 2019 Lid van CSU Fullerton, Team S1-G3, Bruce Fall 2019

CSUF-BRUCE-F19S1G3

4 Leden

2 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 7

Afgelopen 7 dagen: 35

Afgelopen 30 dagen: 209

Altijd: 3,895