Repareer je spullen Gemeenschap Winkel

How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation)

Inleiding

If your Cubify Printer has stopped printing and refuses to start a new print, this guide to remove a clog in a Cubify White Cube 3D Printer (3rd Generation) filament cartridge.

The injector needles transfer the plastic filament to the printing bed and also layer the plastic. A clogged injector can damage the cartridge and ruin the filament.

Wat je nodig hebt

  1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation), How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 1, afbeelding 1 van 2 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation), How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 1, afbeelding 2 van 2

    • On the top of the printer, turn the injector counter-clockwise and pull the tab.

    Bewerken

  2. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 2, afbeelding 1 van 3 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 2, afbeelding 2 van 3 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 2, afbeelding 3 van 3

    • Insert your fingers in the center of the filament cartridge and slowly pull it away from the printer.

    Bewerken

  3. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 3, afbeelding 1 van 1

    • Place the cartridge face up and pry off the lid of the cartridge.

    Bewerken

  5. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 4, afbeelding 1 van 2 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 4, afbeelding 2 van 2

    • Gently flip the cartridge on its front and remove the two 2mm Hex screws using a Hex key.

    Bewerken

  6. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 5, afbeelding 1 van 1

    • Flip the cartridge face up and remove the gearbox and extractor tube.

    Bewerken

  7. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 6, afbeelding 1 van 3 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 6, afbeelding 2 van 3 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 6, afbeelding 3 van 3

    • Place your thumb on the front of the injector head and your middle finger on the needle.

    • Firmly pull the needle towards your thumb until the injector head cases cracks and pulls apart the case.

    Bewerken

  8. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 7, afbeelding 1 van 2 How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 7, afbeelding 2 van 2

    • Heat the needle using a lighter, making sure that the flame does not touch the needle.

    • Using needle-nose pliers, pull the needle from the tube.

    • Do not touch the needle as it may still be hot.

    Bewerken

  9. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): stap 8, afbeelding 1 van 1

    • Insert a paper clip and turn until the clog is removed.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 2 andere bijdragers

Hector Vazquez

Lid sinds: 10/23/20

157 Reputatie

1 Handleiding geschreven

Medailles: 2

Team

CSU Los Angeles, Team S12-G11, Harris Fall 2020 Lid van CSU Los Angeles, Team S12-G11, Harris Fall 2020

CSULA-HARRIS-F20S12G11

1 Lid

2 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 11

Altijd: 509