Repareer je spullen Gemeenschap Winkel

Hover-1 Folding E-Scooter Rear Wheel Replacement

Inleiding

This guide is created to replace a damaged or broken back wheel. Tools required are a Hex Bit 4.0 tool, a bit extender, and an allen key.

Wat je nodig hebt

  1. Hover-1 Folding E-Scooter Rear Wheel Replacement, Rear Wheel: stap 1, afbeelding 1 van 2 Hover-1 Folding E-Scooter Rear Wheel Replacement, Rear Wheel: stap 1, afbeelding 2 van 2

    • Remove either of the two 0.2 mm axle screws by using a hex bit 4.0 by turning clockwise.

    • The two screws are the same thread so find the screw that has the least torque. Only that screw will be able to removed in this step.

    • Turn the hex bit 4.0 counterclockwise to reassemble the axle screws.

    Vertaal

  2. Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 2, afbeelding 1 van 3 Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 2, afbeelding 2 van 3 Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 2, afbeelding 3 van 3

    • Slide off the plastic side panel.

    Vertaal

  4. Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 3, afbeelding 1 van 1

    • Use a hex bit 4.0 to screw back in the 0.2 mm screw as tightly as possible by turning clockwise.

    • You will need to hold the other screw you are not replacing with an additional hex bit 4.0, so that the screws don't spin freely.

    Vertaal

  5. Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 4, afbeelding 1 van 1

    • Flip over the scooter and use the hex bit 4.0 to remove the other 0.2 mm screw.

    Vertaal

  6. Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 5, afbeelding 1 van 3 Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 5, afbeelding 2 van 3 Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 5, afbeelding 3 van 3

    • Slide off the other plastic side panel.

    Vertaal

  7. Hover-1 Folding E-Scooter Rear Wheel Replacement: stap 6, afbeelding 1 van 1

    • On the same side you removed the screw, use the bit extender to push down on the axle inside the wheel.

    • The axle pops out and the wheel easily comes off.

    • Two washers will pop out with the axle.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 4 andere bijdragers

Luke Imai

Lid sinds: 10/08/18

133 Reputatie

1 Handleiding geschreven

Medailles: 2

Team

Cal Poly, Team S15-G5, White Fall 2018 Lid van Cal Poly, Team S15-G5, White Fall 2018

CPSU-WHITE-F18S15G5

4 Leden

5 handleidingen geschreven

2 opmerkingen

Where can you get replacement rubber for the front and rear wheels?

jackricotta - Antwoord

How about adding a rear wheel removal article for the Hover-1 Alpha folding scooter?

sfaheysd - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 12

Afgelopen 30 dagen: 36

Altijd: 5,158