Repareer je spullen Gemeenschap Winkel

Hover-1 Coast Power Button Spring Replacement

Inleiding

If your Hover-1 Coast board’s power button won't press you likely have an issue with the button spring. This spring allows the button to be compressed, sending a signal to the battery to turn on and power the board.

This will be a moderately difficult task to complete as you will use tools that not everyone probably has but are common for most electronics repairs.


Provided to you, is a list of detailed instructions on how to properly, and safely replace the spring. For parts please go ++here++ to look at how to purchase new parts. For any inquiries, please take a look at the operator’s manual link ++here++.

Wat je nodig hebt

  1. Hover-1 Coast Power Button Spring Replacement, Board Battery: stap 1, afbeelding 1 van 3 Hover-1 Coast Power Button Spring Replacement, Board Battery: stap 1, afbeelding 2 van 3 Hover-1 Coast Power Button Spring Replacement, Board Battery: stap 1, afbeelding 3 van 3

    • To remove the battery on the Hover-1 Coast, you must uncover the screws on the top of the board.

    • Using a pick tool, puncture the grip tape and expose the screws.

    • Loosen all four 1" screws using a Phillips #1 screwdriver.

    Bewerken

  2. Hover-1 Coast Power Button Spring Replacement: stap 2, afbeelding 1 van 3 Hover-1 Coast Power Button Spring Replacement: stap 2, afbeelding 2 van 3 Hover-1 Coast Power Button Spring Replacement: stap 2, afbeelding 3 van 3

    • Now pull the black protective cover off the board.

    • Locate the battery.

    Bewerken

  4. Hover-1 Coast Power Button Spring Replacement: stap 3, afbeelding 1 van 3 Hover-1 Coast Power Button Spring Replacement: stap 3, afbeelding 2 van 3 Hover-1 Coast Power Button Spring Replacement: stap 3, afbeelding 3 van 3

    • The battery is connected by these two sets of wires.

    • Remove the yellow wire first by pulling the two wires gently in opposite directions.

    • Now pull apart the black wire by gently pulling the two wires in opposite directions.

    Bewerken

  5. Hover-1 Coast Power Button Spring Replacement: stap 4, afbeelding 1 van 3 Hover-1 Coast Power Button Spring Replacement: stap 4, afbeelding 2 van 3 Hover-1 Coast Power Button Spring Replacement: stap 4, afbeelding 3 van 3

    • Once the battery has been disconnected, gently pry the battery upward.

    • It is important to use a plastic opening tool to avoid puncturing the battery.

    • Once the battery is freed, remove it with your hands.

    • The battery is glued to the case and will require some effort to remove.

    Bewerken

  6. Hover-1 Coast Power Button Spring Replacement, Power Button Spring: stap 5, afbeelding 1 van 3 Hover-1 Coast Power Button Spring Replacement, Power Button Spring: stap 5, afbeelding 2 van 3 Hover-1 Coast Power Button Spring Replacement, Power Button Spring: stap 5, afbeelding 3 van 3

    • Using the Phillips #1 screwdriver, loosen the two screws and place the power button somewhere safe.

    Bewerken

  7. Hover-1 Coast Power Button Spring Replacement: stap 6, afbeelding 1 van 2 Hover-1 Coast Power Button Spring Replacement: stap 6, afbeelding 2 van 2

    • Remove the unwanted spring and place your new spring back into the hole.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 3

Afgelopen 30 dagen: 4

Altijd: 345