Repareer je spullen Gemeenschap Winkel

Hipstreet Titan 2 HD Speaker Replacement

Inleiding

Use this guide to replace the speaker. First you'll need to remove the rear cover. This can be a difficult process.

Wat je nodig hebt

  1. Hipstreet Titan 2 HD Speaker Replacement, Rear Case: stap 1, afbeelding 1 van 1

    • Using the PH#00 screwdriver, remove the two 0.145 inch Phillips head screws.

    • The screws are located on the bottom face of the device, near the power and volume controls.

    Bewerken

  2. Hipstreet Titan 2 HD Speaker Replacement: stap 2, afbeelding 1 van 1

    • Place the small suction cup on your screen.

    • Moisturize the bottom of the suction cup to ensure a proper seal.

    • If the screen is cracked, the suction cup may not seal correctly; too much pressure may crack or damage the screen.

    Bewerken

  3. Hipstreet Titan 2 HD Speaker Replacement: stap 3, afbeelding 1 van 1

    • Insert the plastic opening tool between the screen cover and rear cover of the tablet.

    • Grasp the small suction cup.

    Bewerken

  4. Hipstreet Titan 2 HD Speaker Replacement: stap 4, afbeelding 1 van 2 Hipstreet Titan 2 HD Speaker Replacement: stap 4, afbeelding 2 van 2

    • Slide the plastic opening tool along device edge to separate the screen cover from the rear cover.

    • Pull upward on the small suction cup handle while sliding the opening tool.

    • When sliding the plastic opening tool, avoid sliding the tool too far into the cover. This could damage the speaker connector on the back cover.

    Bewerken

  6. Hipstreet Titan 2 HD Speaker Replacement: stap 5, afbeelding 1 van 2 Hipstreet Titan 2 HD Speaker Replacement: stap 5, afbeelding 2 van 2

    • Use the plastic opening tool to remove the speaker from the rear cover.

    • The speaker is held in place with adhesive and is easily removed.

    • Do not pull on the speaker wires. This could damage the soldering connections.

    Bewerken

  7. Hipstreet Titan 2 HD Speaker Replacement: stap 6, afbeelding 1 van 1

    • Once the speaker is disconnected, the cover removal is complete.

    Bewerken

  8. Hipstreet Titan 2 HD Speaker Replacement, Speaker: stap 7, afbeelding 1 van 1

    • Remove the black placement tape.

    Bewerken

  9. Hipstreet Titan 2 HD Speaker Replacement: stap 8, afbeelding 1 van 1

    • Using a #PH000 screwdriver, remove the three 0.145in circuit board placement screws.

    Bewerken

  10. Hipstreet Titan 2 HD Speaker Replacement: stap 9, afbeelding 1 van 3 Hipstreet Titan 2 HD Speaker Replacement: stap 9, afbeelding 2 van 3 Hipstreet Titan 2 HD Speaker Replacement: stap 9, afbeelding 3 van 3

    • Lift the hinge locks on the three ribbon connectors and disconnect the ribbon connectors.

    Bewerken

  11. Hipstreet Titan 2 HD Speaker Replacement: stap 10, afbeelding 1 van 1

    • Identify the two soldered connectors for the speaker.

    Bewerken

  12. Hipstreet Titan 2 HD Speaker Replacement: stap 11, afbeelding 1 van 1

    • Using a solder removal tool, remove the speaker soldered connectors.

    • Solder the new speaker wire connections to circuit board.

    • First solder the red wire on the left, then the black wire on the right.

    • Solder can burn you. Use caution.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Auteur

met 7 andere bijdragers

Jeffrey

Lid sinds: 03/11/15

766 Reputatie

5 handleidingen geschreven

Medailles: 10

+7 andere badges

Team

Colorado Springs, Team 5-6, Panko Spring 2015 Lid van Colorado Springs, Team 5-6, Panko Spring 2015

UCCS-PANKO-S15S5G6

3 Leden

10 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 0

Altijd: 304