Repareer je spullen Gemeenschap Winkel

HP TouchSmart 15-r015dx Screen Replacement

Geschreven door: Gabriel Terrasas (en 2 andere bijdragers)
  • Reacties: 1
  • Favorieten: 2
  • Voltooide reparaties: 3

Moeilijkheid

Gemiddeld

Stappen

12

Tijd vereist

45 minuten - 1 uur

Secties

1

Markeringen

2

Incorrect Tools

Onjuiste gereedschappen

Help om deze handleiding beter te maken door de juiste gereedschappen in plaatjes en/of tekst te gebruiken.

Better Introduction

Betere introductie

Verbeter deze handleiding door het afmaken of herzien van de introductie.

Inleiding

Use this guide to lead in the replacement of your HP TouchSmart 15 screen.

Gereedschap

Onderdelen

Geen onderdelen opgegeven.

  1. Acquire the metal spudger and a Precision Magnetized Driver with J1 size bit. Flip your HP TouchSmart 15 over. Flip your HP TouchSmart 15 over.

    • Acquire the metal spudger and a Precision Magnetized Driver with J1 size bit.

    • Flip your HP TouchSmart 15 over.

    Bewerken

  2. Locate tabs on the underside of the laptop. Push both tabs towards the center of the laptop and pull away to remove battery. Push both tabs towards the center of the laptop and pull away to remove battery.

    • Locate tabs on the underside of the laptop.

    • Push both tabs towards the center of the laptop and pull away to remove battery.

    Bewerken

  3. Take the sharp end of the pry tool and pop out the black screw cover. Repeat on opposite side. Repeat on opposite side.

    • Take the sharp end of the pry tool and pop out the black screw cover.

    • Repeat on opposite side.

    Bewerken

  4. Take the Precision Magnetized Driver with J1 size bit and unscrew the screw. Repeat on opposite side. Repeat on opposite side.

    • Take the Precision Magnetized Driver with J1 size bit and unscrew the screw.

    • Repeat on opposite side.

    Bewerken

  6. Using the pry tool, begin to separate the touchscreen from the plastic backing. Using the pry tool, begin to separate the touchscreen from the plastic backing. Using the pry tool, begin to separate the touchscreen from the plastic backing.

    • Using the pry tool, begin to separate the touchscreen from the plastic backing.

    Bewerken

  7. Close the laptop and flip it over once again. Continue to pry the touchscreen from the plastic backing in the hinged area of the laptop. Continue to pry the touchscreen from the plastic backing in the hinged area of the laptop.

    • Close the laptop and flip it over once again.

    • Continue to pry the touchscreen from the plastic backing in the hinged area of the laptop.

    Bewerken

  8. Flip over the laptop and open it. Pull up on the separated touchscreen while pulling it away from the plastic backing. Be careful while laying down the touchscreen to not pull the connection point.

    • Flip over the laptop and open it.

    • Pull up on the separated touchscreen while pulling it away from the plastic backing.

    • Be careful while laying down the touchscreen to not pull the connection point.

    • Lay the touchscreen on the keyboard facedown.

    Bewerken

  9. Locate the connection point. Slowly and carefully peel off. Slowly and carefully peel off.

    • Locate the connection point.

    • Slowly and carefully peel off.

    Bewerken

  10. Isolate the touchscreen from the keyboard. Isolate the touchscreen from the keyboard.

    • Isolate the touchscreen from the keyboard.

    Bewerken

  11. Begin by peeling off the black adhesive tape using the pry tool. Once adhesive tape is removed, use the pry tool to remove the tab in the corner. Repeat in each corner. Once adhesive tape is removed, use the pry tool to remove the tab in the corner. Repeat in each corner.

    • Begin by peeling off the black adhesive tape using the pry tool.

    • Once adhesive tape is removed, use the pry tool to remove the tab in the corner. Repeat in each corner.

    Bewerken

  12. Using the sharp end of the pry tool, separate the plastic from the screen. Using the sharp end of the pry tool, separate the plastic from the screen. Using the sharp end of the pry tool, separate the plastic from the screen.

    • Using the sharp end of the pry tool, separate the plastic from the screen.

    Bewerken

  13. Now it is time to reassemble your device with a new screen.

    • Now it is time to reassemble your device with a new screen.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

Auteur

met 2 andere bijdragers

Gabriel Terrasas

Lid sinds: 30-11-17

304 Reputatie

1 Handleiding geschreven

Badges: 6

+3 andere badges

Team

Coast Union High School, Team S1-G1, Hartzell Fall 2017 Lid van Coast Union High School, Team S1-G1, Hartzell Fall 2017

CUHS-HARTZELL-F17S1G1

2 Leden

1 handleiding geschreven

Één commentaar

Amazing work. I would not change a thing.

Dan Hartzell - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 8

Altijd: 986