Repareer je spullen

Recht op reparatie

Winkel

HP Photosmart 935 LCD Screen Replacement

Aanbevolen

Geschreven door: Nick Oleskowicz (en 10 andere bijdragers)
  • Reacties: 0
  • Favorieten: 5
  • Voltooide reparaties: 1

Uitgelichte handleiding

Moeilijkheid

Gemiddeld

Stappen

16

Tijd vereist

20 - 30 minuten

Secties

3

Markeringen

3

Grammar Police

Grammaticapolitie

Laat je innerlijke leraar Nederlands vrij en help om de grammatica van deze handleiding te verbeteren!

Needs Better Images

Heeft betere plaatjes nodig

Betere foto's zullen deze handleiding verbeteren. Help mee door het nemen, bewerken of uploaden van nieuwe foto's!

Featured Guide

Uitgelichte handleiding

De iFixit-werknemers vonden deze handleiding uitzonderlijk cool.

Inleiding

The purpose of this guide is to teach reader to install a new LCD screen. If the current LCD screen is broken or cracked, this guide will help the reader to replace it with a new one.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Flip the camera over so the bottom is facing you. Flip the camera over so the bottom is facing you.

    • Flip the camera over so the bottom is facing you.

    Bewerken

  2. Open the cover on the bottom by sliding it in the direction of the arrow. Open the cover on the bottom by sliding it in the direction of the arrow.

    • Open the cover on the bottom by sliding it in the direction of the arrow.

    Bewerken

  3. Remove the batteries by pulling up on the top with your fingers.

    • Remove the batteries by pulling up on the top with your fingers.

    Bewerken

  4. Unless otherwise stated, use a Phillips #00 screwdriver to remove screws.

    • Unless otherwise stated, use a Phillips #00 screwdriver to remove screws.

    • Remove the two 4.70mm screws in the bottom of the plastic casing.

    Bewerken

  5. Remove the four 4.70mm screws in the left side of the camera. Remove the four 4.70mm screws in the left side of the camera.

    • Remove the four 4.70mm screws in the left side of the camera.

    Bewerken

  6. Now on the side with the strap, remove the other four 4.70mm screws. Now on the side with the strap, remove the other four 4.70mm screws.

    • Now on the side with the strap, remove the other four 4.70mm screws.

    Bewerken

  7. De essentiële toolkit

    De meest behulpzame tools in onze meest compacte kit.

    Koop nu

    De essentiële toolkit

    De meest behulpzame tools in onze meest compacte kit.

    Koop nu

  8. Use your thumbs to pry the case apart. It is easiest to pry to case apart if your start at the bottom. The case should come apart with minimal effort. If it doesn't, you can use a tool such as a spudger or plastic opening tool.

    • Use your thumbs to pry the case apart.

    • It is easiest to pry to case apart if your start at the bottom.

    • The case should come apart with minimal effort. If it doesn't, you can use a tool such as a spudger or plastic opening tool.

    Bewerken

  9. This step requires a significant amount of force.

    • This step requires a significant amount of force.

    • Pull the bottom half of the inner camera out of case about half an inch. This may be difficult and force is necessary.

    Bewerken

  10. While pulling the camera out of the case, note the small soft plastic cover on the side of the camera. This cover will detach from the rest of the device. Once the bottom of the inner camera is pulled out about an inch and a half, pull the device out completely.

    • While pulling the camera out of the case, note the small soft plastic cover on the side of the camera. This cover will detach from the rest of the device.

    • Once the bottom of the inner camera is pulled out about an inch and a half, pull the device out completely.

    • When completely removing the device from the case, use a firm grasp with your hands for stability and control.

    Bewerken

  11. Orient the camera so that the LCD screen is facing you.

    • Orient the camera so that the LCD screen is facing you.

    • If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.

    • Removing the casing completely is crucial to completing this guide.

    Bewerken

  12. Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame. Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame.

    • Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame.

    Bewerken

  13. Allow the LCD screen to flip down. This will expose the electric strip that connects the screen to the camera.

    • Allow the LCD screen to flip down. This will expose the electric strip that connects the screen to the camera.

    Bewerken

  14. Look for where the yellow electric strip is attached to the camera. You will find a plastic grey bar and a white base holding this strip in place.

    • Look for where the yellow electric strip is attached to the camera. You will find a plastic grey bar and a white base holding this strip in place.

    • Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.

    Bewerken

  15. Unplug the connected red and white wires. They will come out with the small white casing.

    • Unplug the connected red and white wires. They will come out with the small white casing.

    Bewerken

  16. Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.

    • Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.

    Bewerken

  17. Remove the bottom left LCD mounting frame screw. The screen should come loose after the screw is removed. Remove the LCD screen from the camera. Make sure that the electric strip comes out with screen.

    • Remove the bottom left LCD mounting frame screw. The screen should come loose after the screw is removed.

    • Remove the LCD screen from the camera. Make sure that the electric strip comes out with screen.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 10 andere bijdragers

Nick Oleskowicz

Lid sinds: 03-04-12

263 Reputatie

3 handleidingen geschreven

Badges: 8

+5 andere badges

Team

Cal Poly, Team 15-13, Forte Spring 2012 Lid van Cal Poly, Team 15-13, Forte Spring 2012

CPSU-FORTE-S12S15G13

5 Leden

10 handleidingen geschreven

0 Opmerkingen

Voeg een opmerking toe

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 17

Altijd: 2,024