Repareer je spullen Gemeenschap Winkel

HP Envy 700-030qe Solid State Drive Replacement

Inleiding

Whatever the reason is that you want to replace your hard drive, this guide will show you how to do just that! Whether it is broken or you want to upgrade your hard drive this guide will show you what to do.

Wat je nodig hebt

  1. HP Envy 700-030qe Solid State Drive Replacement, Solid State Drive: stap 1, afbeelding 1 van 1

    • Before beginning, it is good to wear an anti-static wrist band to prevent electrical components from getting harmed.

    • Attach the anti-static wristband to your wrist, and clip the other end to an exposed piece of metal anywhere on the case.

    Bewerken

  2. HP Envy 700-030qe Solid State Drive Replacement: stap 2, afbeelding 1 van 1

    • Start by opening the device case by unscrewing the 10.5mm hand screw on the back of the computer.

    • If the hand screw is too tight, you may use the Torx T15 screwdriver to remove it.

    Bewerken

  3. HP Envy 700-030qe Solid State Drive Replacement: stap 3, afbeelding 1 van 1

    • Turn the computer onto its side to continue removing the case cover.

    • Slide the cover off by sliding it to the right.

    Bewerken

  5. HP Envy 700-030qe Solid State Drive Replacement: stap 4, afbeelding 1 van 2 HP Envy 700-030qe Solid State Drive Replacement: stap 4, afbeelding 2 van 2

    • Locate the SSD inside the open case.

    • Unplug the SATA power cable from the hard drive by pulling straight up.

    Bewerken

  6. HP Envy 700-030qe Solid State Drive Replacement: stap 5, afbeelding 1 van 1

    • Finish disconnecting the hard drive by unplugging the black SATA interface cable by pulling up.

    Bewerken

  7. HP Envy 700-030qe Solid State Drive Replacement: stap 6, afbeelding 1 van 1

    • To remove the SSD and its casing, pull out on the side silver tab.

    • At the same time, pull up on the hard drive. It should slide out smoothly without much effort.

    Bewerken

  8. HP Envy 700-030qe Solid State Drive Replacement: stap 7, afbeelding 1 van 1

    • To completly remove the SSD from its casing, unscrew the four 5mm screws on opposite ends of the casing. Use a Torx T15 screw driver to accomplish this.

    • Notice that the screws to remove are the four screws inside the holes rather than the screws that are next to the holes.

    Bewerken

  9. HP Envy 700-030qe Solid State Drive Replacement: stap 8, afbeelding 1 van 1

    • Finally, slide the SSD out of the casing.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

4 andere personen hebben deze handleiding voltooid.

Auteur

met 3 andere bijdragers

Chandler Warne

Lid sinds: 10/01/15

273 Reputatie

1 Handleiding geschreven

Medailles: 12

+9 andere badges

Team

Cal Poly, Team 5-9, Maness Fall 2015 Lid van Cal Poly, Team 5-9, Maness Fall 2015

CPSU-MANESS-F15S5G9

4 Leden

10 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 10

Altijd: 2,501