Repareer je spullen Gemeenschap Winkel

Graco Secure Coverage LED Nursery Unit Replacement

Inleiding

Use this guide to replace the LED on your Graco Secure Coverage Digital Baby Monitor for nursery unit.

The LED replacement includes the LED and battery replacement.

Wat je nodig hebt

  1. Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: stap 1, afbeelding 1 van 3 Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: stap 1, afbeelding 2 van 3 Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: stap 1, afbeelding 3 van 3

    • Remove the 9mm screw from the battery cover of the nursery unit using a Phillips #1 tip screwdriver.

    Vertaal

  2. Graco Secure Coverage LED Nursery Unit Replacement: stap 2, afbeelding 1 van 2 Graco Secure Coverage LED Nursery Unit Replacement: stap 2, afbeelding 2 van 2

    • Using the plastic opening tool, pry and remove the battery cover carefully.

    • Remove the batteries using plastic opening tool.

    • Replace the batteries.

    Vertaal

  4. Graco Secure Coverage LED Nursery Unit Replacement, LED Nursery Unit: stap 3, afbeelding 1 van 2 Graco Secure Coverage LED Nursery Unit Replacement, LED Nursery Unit: stap 3, afbeelding 2 van 2

    • Remove the two 9mm Phillips #1 screws from the rare case of the device.

    • Place the screws in a secure place.

    Vertaal

  5. Graco Secure Coverage LED Nursery Unit Replacement: stap 4, afbeelding 1 van 1

    • Hold the bottom of the device with one hand and pull down to separate the front and rare cases.

    • While holding the device with one hand, use plastic opening tool to pry the edges of the front case away from the back case.

    • Apply constant force carefully to avoid breaking any other plastic parts from the device.

    Vertaal

  6. Graco Secure Coverage LED Nursery Unit Replacement: stap 5, afbeelding 1 van 2 Graco Secure Coverage LED Nursery Unit Replacement: stap 5, afbeelding 2 van 2

    • Remove all three 7mm Phillips #1 screws from the mother board.

    • Place the screws in secure place.

    Vertaal

  7. Graco Secure Coverage LED Nursery Unit Replacement: stap 6, afbeelding 1 van 3 Graco Secure Coverage LED Nursery Unit Replacement: stap 6, afbeelding 2 van 3 Graco Secure Coverage LED Nursery Unit Replacement: stap 6, afbeelding 3 van 3

    • Flip over the motherboard to look at the LED pins that are connected to it.

    • Solder off the LED pin from the motherboard.

    • There are many pins are connect to the motherboard, so make sure that you solder off the LED pin.

    • Replace the LED.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 2 andere bijdragers

Bryson Wolff

Lid sinds: 08/31/15

237 Reputatie

2 handleidingen geschreven

Medailles: 10

+7 andere badges

Team

USF Tampa, Team 6-5, Remmell Fall 2015 Lid van USF Tampa, Team 6-5, Remmell Fall 2015

USFT-REMMELL-F15S6G5

4 Leden

8 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 11

Altijd: 162