Repareer je spullen Gemeenschap Winkel

Graco Secure Coverage Speaker Replacement on Parent Unit

Inleiding

Use this guide to replace the speaker on your Graco Secure Coverage Digital Baby Monitor for parent unit.

The speaker replacement includes the speaker and battery replacement.

Wat je nodig hebt

  1. Graco Secure Coverage Speaker Replacement on Parent Unit, Parent Unit Battery: stap 1, afbeelding 1 van 3 Graco Secure Coverage Speaker Replacement on Parent Unit, Parent Unit Battery: stap 1, afbeelding 2 van 3 Graco Secure Coverage Speaker Replacement on Parent Unit, Parent Unit Battery: stap 1, afbeelding 3 van 3

    • Using plastic opening tool, pry and remove the battery lid.

    Vertaal

  2. Graco Secure Coverage Speaker Replacement on Parent Unit: stap 2, afbeelding 1 van 1

    • Remove the battery by holding the device with one hand and pulling the battery out with other hand carefully.

    • Make sure that you disconnect the battery's wire before you remove the battery.

    Vertaal

  3. Graco Secure Coverage Speaker Replacement on Parent Unit, Parent Unit Speaker: stap 3, afbeelding 1 van 2 Graco Secure Coverage Speaker Replacement on Parent Unit, Parent Unit Speaker: stap 3, afbeelding 2 van 2

    • There are two screws on the rare case of the device. For the one shown in red marker requires either an extended screwdriver or putting on a little pressure on a regular screwdriver.

    • Remove the two 9mm Phillips #1 screws from the rare case of the device.

    • If you cannot remove the screw with low pressure, do not use high pressure to remove it. It may cause a damage on the device case. Use an extended screwdriver instead.

    Vertaal

  5. Graco Secure Coverage Speaker Replacement on Parent Unit: stap 4, afbeelding 1 van 2 Graco Secure Coverage Speaker Replacement on Parent Unit: stap 4, afbeelding 2 van 2

    • Using opening plastic tool, pry the two grey cases from both sides of the device.

    • Take your time and apply constant force to avoid breaking or damaging any other plastic parts.

    • While pry off the grey cases, hold the device with your other hand to remove the cases.

    Vertaal

  6. Graco Secure Coverage Speaker Replacement on Parent Unit: stap 5, afbeelding 1 van 1

    • Pry the edges of the device to separate the front case away from the rare case.

    • While prying the edges, hold the device with one hand to pull out each case a part.

    • Make sure you use a constant force, and the pushbuttons are pried off completely.

    Vertaal

  7. Graco Secure Coverage Speaker Replacement on Parent Unit: stap 6, afbeelding 1 van 2 Graco Secure Coverage Speaker Replacement on Parent Unit: stap 6, afbeelding 2 van 2

    • Remove the 7mm Phillips #1 screw from the mother board.

    • Place the screw in a secure place.

    • Pull out the mother board away from the case carefully.

    Vertaal

  8. Graco Secure Coverage Speaker Replacement on Parent Unit: stap 7, afbeelding 1 van 2 Graco Secure Coverage Speaker Replacement on Parent Unit: stap 7, afbeelding 2 van 2

    • Pick up the motherboard.

    • Solder off the speaker from the device's case.

    • Solder off the speaker from the mother board.

    • There are many pins attached to the mother board, make sure you solder off the proper pins that attached to the speaker wires.

    • Replace the speaker.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 5 andere bijdragers

Ahmed Elshaer

Lid sinds: 09/09/15

201 Reputatie

2 handleidingen geschreven

Medailles: 6

+3 andere badges

Team

USF Tampa, Team 6-5, Remmell Fall 2015 Lid van USF Tampa, Team 6-5, Remmell Fall 2015

USFT-REMMELL-F15S6G5

4 Leden

8 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 6

Altijd: 172