Ga door naar hoofdinhoud

GoPro Hero 3 Silver LCD Housing Replacement

Wat je nodig hebt

  1. GoPro Hero 3 Silver LCD Housing Replacement, Battery: stap 1, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement, Battery: stap 1, afbeelding 2 van 2
    • Pull back on the tab on the back of GoPro to open the battery cover.

  2. GoPro Hero 3 Silver LCD Housing Replacement: stap 2, afbeelding 1 van 1
    • Pull the battery out using the tab.

  3. GoPro Hero 3 Silver LCD Housing Replacement, LCD Housing: stap 3, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement, LCD Housing: stap 3, afbeelding 2 van 2
    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

  4. GoPro Hero 3 Silver LCD Housing Replacement: stap 4, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement: stap 4, afbeelding 2 van 2
    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

  5. GoPro Hero 3 Silver LCD Housing Replacement: stap 5, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement: stap 5, afbeelding 2 van 2
    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

  6. GoPro Hero 3 Silver LCD Housing Replacement: stap 6, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement: stap 6, afbeelding 2 van 2
    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

  7. GoPro Hero 3 Silver LCD Housing Replacement: stap 7, afbeelding 1 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 7, afbeelding 2 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 7, afbeelding 3 van 3
    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

  8. GoPro Hero 3 Silver LCD Housing Replacement: stap 8, afbeelding 1 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 8, afbeelding 2 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 8, afbeelding 3 van 3
    • The media adapter is attached to the motherboard via 3 screws:

    • x1 T4 Torx

    • x2 Phillips #00

    • There's a little silver bracket that is held down by the Phillips #00 screw so be careful not to lose it.

    • With a little prying, use the spudger to detach the media adapter's connector from the motherboard.

  9. GoPro Hero 3 Silver LCD Housing Replacement: stap 9, afbeelding 1 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 9, afbeelding 2 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 9, afbeelding 3 van 3
    • Use the spudger to lift the black tab up to unlock.

    • Then remove LCD screen connector by sliding out.

  10. GoPro Hero 3 Silver LCD Housing Replacement: stap 10, afbeelding 1 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 10, afbeelding 2 van 3 GoPro Hero 3 Silver LCD Housing Replacement: stap 10, afbeelding 3 van 3
    • Using the Phillips head bit, remove the silver screw near the the top edge of the board.

    • Separate the LCD assembly by pulling away the motherboard.

  11. GoPro Hero 3 Silver LCD Housing Replacement: stap 11, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement: stap 11, afbeelding 2 van 2
    • There are 3 Phillips #00 screws holding the lens onto the LCD housing that need to be removed.

    • Our screw on the top right is stripped, which is why it looks different. However, they will all look the same in your device.

  12. GoPro Hero 3 Silver LCD Housing Replacement: stap 12, afbeelding 1 van 2 GoPro Hero 3 Silver LCD Housing Replacement: stap 12, afbeelding 2 van 2
    • Carefully remove the camera lens from the LCD Housing.

    • Now you have the LCD housing removed!

Conclusie

To reassemble your device, follow these instructions in reverse order.

5 andere personen hebben deze handleiding voltooid.

Brian Alvarez

Lid sinds: 04/02/15

1.439 Reputatie

6 handleidingen geschreven

Team

Cal Poly, Team 24-7, Lancaster Spring 2015 Lid van Cal Poly, Team 24-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G7

3 Leden

21 handleidingen geschreven

Één opmerking

Excellent walkthrough. Thank you Brian!

Nick Goulet - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 15

Altijd: 8,657