Ga door naar hoofdinhoud

GoPro Hero 3 Silver Image Sensor Replacement

Wat je nodig hebt

  1. GoPro Hero 3 Silver Image Sensor Replacement, Battery: stap 1, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement, Battery: stap 1, afbeelding 2 van 2
    • Pull back on the tab on the back of GoPro to open the battery cover.

  2. GoPro Hero 3 Silver Image Sensor Replacement: stap 2, afbeelding 1 van 1
    • Pull the battery out using the tab.

  3. GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: stap 3, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: stap 3, afbeelding 2 van 2
    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

  4. GoPro Hero 3 Silver Image Sensor Replacement: stap 4, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement: stap 4, afbeelding 2 van 2
    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

  5. GoPro Hero 3 Silver Image Sensor Replacement: stap 5, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement: stap 5, afbeelding 2 van 2
    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

  6. GoPro Hero 3 Silver Image Sensor Replacement: stap 6, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement: stap 6, afbeelding 2 van 2
    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

  7. GoPro Hero 3 Silver Image Sensor Replacement: stap 7, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement: stap 7, afbeelding 2 van 2
    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

  8. GoPro Hero 3 Silver Image Sensor Replacement: stap 8, afbeelding 1 van 2 GoPro Hero 3 Silver Image Sensor Replacement: stap 8, afbeelding 2 van 2
    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

    • You should now be able to remove the image sensor by simply pulling it.

Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Jose Villa

Lid sinds: 04/01/15

297 Reputatie

1 Handleiding geschreven

Team

Cal Poly, Team 24-7, Lancaster Spring 2015 Lid van Cal Poly, Team 24-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G7

3 Leden

21 handleidingen geschreven

2 opmerkingen

After the sensor has been replaced, does the camera need any catibration?

enrilazaro - Antwoord

Your pictures are really dark.

Nick Ruiz - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 2

Afgelopen 30 dagen: 5

Altijd: 1,853