Inleiding

This guide shows how to remove the paper eject frame assembly Constant paper jams might be caused by a faulty paper eject frame assembly. This process requires the knowledge of how to use basic tools.

  1. Turn off the printer.
    • Turn off the printer.

    • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

    Voeg opmerking toe

  2. Locate the IEEE cover in  the back.
    • Locate the IEEE cover in the back.

    • Gently slide cover to the right to unlatch then pull to remove it.

    Voeg opmerking toe

    • Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

    • Remove the 6mm screw that holds the rear housing in place.

    Voeg opmerking toe

    • Remove the rear housing by pulling it backwards.

    Voeg opmerking toe

    • Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

    • Release the two tabs of the side housing by lifting the tool in an upward motion

    • Remove the side housing by pulling it outwards.

    Voeg opmerking toe

    • Both side housings are attached by the same type of mechanism.

    • Using the same method, remove the other side housing.

    Voeg opmerking toe

    • Lift the paper support.

    • Open the printer cover and front cover.

    Voeg opmerking toe

    • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

    • Remove the three 6mm Phillips #2 screws.

    Voeg opmerking toe

    • Detach the tabs from the pins on each side by pulling it outwards.

    Voeg opmerking toe

    • Remove the two 10 mm Phillips #2 screws on the front of the printer.

    Voeg opmerking toe

    • Disconnect the cable on the side by carefully pulling it outwards.

    • You may need to gently rock the cable up and down while pulling.

    Voeg opmerking toe

    • Remove the upper housing by lifting it upwards.

    • It's easier to lift the housing by gripping it from the bottom.

    Voeg opmerking toe

    • Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions.

    Voeg opmerking toe

    • Remove the acetate tape that secure the connector cable.

    Voeg opmerking toe

    • There are six screws that secure the printer mechanism.

    • Using the #2 Phillips screwdriver, remove the three 10mm screws shown.

    Voeg opmerking toe

    • Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism.

    Voeg opmerking toe

    • Remove printer mechanism from lower housing by holding the handles and lifting it upwards.

    Voeg opmerking toe

    • Remove the CD-R unit housing by releasing the two attaching points to the tray base.

    • Pull it outwards diagonally one side at a time.

    Voeg opmerking toe

    • Remove the left frame support plate by removing the two 6mm screws that secure it.

    • Pull it out by hand to free it.

    Voeg opmerking toe

    • Using the #2 Phillips screwdriver, remove the four 6mm screws.

    • Remove the two 8mm screws.

    • The screws are located on the lower sections of the printer.

    Voeg opmerking toe

    • Two guide pins secure the paper EJ assy in place.

    • Remove the two guide pins on the CD/DVD tray base by pulling each pin outward.

    Voeg opmerking toe

    • Remove the paper EJ frame assy by pulling the it towards you.

    Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

27 andere personen hebben deze handleiding voltooid.

Larry Huang

Lid sinds: 12-10-11

704 Reputatie

4 handleidingen geschreven

Team

Cal Poly, Team 17-11, Regan Fall 2011 Lid van Cal Poly, Team 17-11, Regan Fall 2011

CPSU-REGAN-F11S17G11

4 Leden

6 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 2

Afgelopen 7 Dagen: 34

Afgelopen 30 Dagen: 129

Altijd: 12,723